ECSS Structures — Bolted-Joint Analysis (space-systems/ecss/bolted-joint-analysis)
Use when the task is the bolted-joint analysis required by ECSS-E-ST-32C clause 4.6.2.13 -- determining load transfer among fasteners, computing bearing stress and bypass ratio, checking the bearing-bypass interaction criterion, deriving bolt preload from installation torque, and assessing each governing failure mode for metallic-fastener joints, composite bolted joints, and lug joints.
Domain quick reference
- Clause 4.6.2.13 requires that every bolted joint be assessed for load transfer (the fraction of the total applied load carried by each fastener), bearing stress (the compressive contact stress at the fastener hole wall), and the bypass load (the portion of total load that passes through the plate section past a given fastener rather than being transferred by it).
- Load transfer among fasteners in a multi-fastener joint is distributed proportionally to each fastener's axial stiffness: a stiffer fastener attracts a larger share of the load. For a joint with uniform fasteners, each carries an equal fraction.
- Bearing stress is computed as the fastener load divided by the product of fastener diameter and plate thickness (units: N/(mm × mm) = MPa). It must be checked against the material's allowable bearing stress.
- Bypass ratio is the fraction of the total applied load that bypasses a given fastener: (total load − fastener load) / total load. A fastener that transfers all of the load has zero bypass; one at the end of a long joint may have a bypass ratio approaching 1.
- The bearing-bypass interaction criterion combines both effects: the bearing ratio (bearing stress / allowable bearing stress) and the bypass ratio are summed (linear interaction); the result must be ≤ 1.0 for compliance. More conservative interaction curves exist for specific material and laminate families.
- Bolt preload is generated by the installation torque. The simplified relationship is F_preload = T / (K × D), where T is applied torque (N·m), K is the nut factor (dimensionless, approximately 0.2 for standard metallic fasteners), and D is the nominal bolt diameter (m). Preload affects joint stiffness, the friction-carried portion of shear load, and fatigue performance.
- Recognized failure modes for bolted joints: bearing (hole wall crushes), net-section tension (plate fails across the reduced section at the fastener hole), shear-out (plate shears along two planes from the hole edge to the free edge), pull-through (fastener head or nut pulls through a thin sheet), fastener shear (bolt shears at the shear plane), fastener tension (bolt breaks under combined preload and external tension), and fatigue (cyclic load initiates a crack at the hole stress concentration).
Workflow
- Verify the joint type: categorize it as metallic-fastener, composite bolted, or lug joint. Reject any unrecognized type before analysis proceeds.
- Identify all fasteners in the joint, collect each fastener's nominal diameter, plate thickness at the fastener hole, axial stiffness, and material allowable bearing stress. Flag any fastener whose allowable bearing stress has not been set — absent allowables block the margin calculation and must be resolved before compliance can be declared.
- Distribute the total applied load among the fasteners proportionally to their stiffnesses.
- For each fastener, compute the bearing stress and the bypass ratio from the distributed load and the total applied load.
- Compute the margin of safety for bearing: (allowable bearing stress / computed bearing stress) − 1. A negative margin is a finding.
- Check the bearing-bypass interaction: bearing ratio + bypass ratio ≤ 1.0. An interaction value exceeding 1.0 is a finding.
- Where installation torque is specified, derive the preload from the torque, nut factor, and diameter. Note that the preload model here is the simplified scalar formula; a friction-based model is needed when the thread friction coefficient is separately characterized.
- Review all findings. A joint is compliant only when every fastener has a positive bearing margin, no bearing-bypass interaction exceeds 1.0, and all allowable-bearing entries are populated.
Pitfalls
- Applying the total load as the bearing load on every fastener without distributing it — this overstates the bearing stress on each fastener and masks the correct bypass ratio, producing a conservative but incorrect interaction check.
- Ignoring the bypass ratio contribution when the bearing ratio is low — a fastener at the end of a splice joint can have a very high bypass ratio; even with low bearing stress the interaction criterion may exceed 1.0.
- Treating an absent allowable bearing stress as a zero violation — a missing allowable means the material data reference has not been consulted, which is itself a non-compliance finding, not a free pass.
- Using the linear interaction criterion for carbon-fibre reinforced polymer laminates without checking whether the programme's composite structural analysis plan specifies a non-linear or laminate-specific interaction curve — clause 4.6.2.13 references the bearing-bypass envelope from the composite materials data; the linear sum is the default fallback, not the governing criterion for all laminates.
- Omitting fatigue from the failure-mode list when the fastener is subject to cyclic loading — clause 4.6.2.13 includes fatigue as a required check; it cannot be waived by showing adequate static margin.
Behavior contract (gate 3)
The joint-type categorization, load distribution, bearing stress, bypass ratio, bearing-bypass interaction, preload, margin-of-safety, and joint-compliance logic is exercised by the gate 3 contract test: scripts/test_bolted_joint_analysis.py against scripts/bolted_joint_analysis_logic.py (stdlib unittest, offline). Run: python3 scripts/test_bolted_joint_analysis.py
Compliance
- ECSS standards are freely downloadable (ESA); cite the source and paraphrase per standards-map.yaml.
- compliance: STANDARDS-REF, gated: false.
