ECSS Element-Level Mechanical Testing (space-systems/ecss/e1003-el-mechanical)
Use when the task is to plan, execute, or review element-level mechanical tests for a space hardware item per ECSS-E-ST-10C §6.5.2 — covering physical properties, modal survey, static load, spin, transient/sine-burst, acoustic, random vibration, and sinusoidal vibration.
Domain quick reference
- §6.5.2 defines eight test types at element level. Each type falls into one of three families: mass-properties (physical properties), structural (static load, spin, transient/sine-burst), or dynamic (modal survey, acoustic, random vibration, sinusoidal vibration). Every test type must be categorized into its family before its acceptance criteria are evaluated.
- Test levels drive the applied load and duration: qualification levels are higher than acceptance or protoflight levels, and the appropriate level is selected from the verification plan before any test is set up.
- Test sequence is constrained: the physical-properties check must precede all structural and dynamic tests (baseline mass and inertia must be established first); the modal survey must precede all vibration and acoustic tests (the element's frequency response must be known before broadband or swept-sine excitation is applied).
- Each timed test type (random vibration, sinusoidal vibration, acoustic, transient/sine-burst) requires a documented test duration that matches the level specification. A duration that is absent or negative is a test-control anomaly that must be resolved before the test is counted as complete.
- Physical-properties measurements (mass, centre-of-mass offset, moment of inertia) are compared against budgets derived from the system mass budget and balance requirements. An exceedance in any parameter is an open finding.
- Vibration levels (Grms) must lie within ±10 % of specification; acoustic overall SPL must lie within ±3 dB of specification. Both tolerances follow standard industry practice for mechanical test control.
Workflow
- Receive the list of required element-level mechanical tests from the verification plan. For each entry, confirm the test type is one of the eight recognised types; reject any entry with an unknown type before proceeding.
- Categorize each test into its family (mass-properties, structural, or dynamic). Structural and dynamic tests that appear before physical-properties or before modal-survey must be flagged as out-of-sequence.
- For each test, record the nominated test level (acceptance, qualification, or protoflight). Reject any test whose level is not one of those three values.
- For every timed test (random vibration, sinusoidal vibration, acoustic, transient/sine-burst), confirm a positive test duration is on record. Flag any timed test without a documented duration.
- After the physical-properties test, compare measured mass, centre-of-mass offset, and moment of inertia against their respective budgets. Flag each parameter that exceeds its limit.
- After the modal survey, confirm the measured fundamental frequency clears the minimum required frequency derived from the interface control document. Record the frequency margin.
- For static-load tests, apply the safety factor to the limit load and confirm the applied load does not exceed the result. Record the load margin.
- For vibration tests, compare applied Grms against the specification. Flag the test if the measured level falls outside the ±10 % control band.
- For acoustic tests, compare the measured overall SPL against specification. Flag any deviation exceeding ±3 dB.
- Aggregate all findings per test type; an element is not mechanically verified until every test is present, correctly sequenced, at a valid level, and has no open findings.
Pitfalls
- Skipping the physical-properties check on the assumption that the element mass is known from the design — the test measurement is the formal record; an analysis value does not close the verification.
- Running vibration or acoustic tests before the modal survey — the element's resonant frequencies must be known in advance so that sweep rates and dwell times can be set safely and exceedances can be interpreted correctly.
- Treating a vibration level that is slightly over the upper control band as acceptable because the element survived — an out-of-band level means the test conditions are not representative of the required environment, which invalidates the result regardless of outcome.
- Applying a qualification load level to an acceptance-only item — over-testing can consume structural fatigue life allocated for the operational mission.
- Leaving a timed test duration unrecorded and reading the test as complete — duration is a primary test-control parameter; its absence makes the test non-traceable and prevents comparison with the qualification baseline.
Behavior contract (gate 3)
The test-type categorization, physical-properties budget check, modal-survey frequency margin, static-load margin, vibration-level control-band check, acoustic-level control-band check, test-sequence ordering, and test-level validation logic are exercised by the gate 3 contract test: scripts/test_e1003_el_mechanical.py against scripts/e1003_el_mechanical_logic.py (stdlib unittest, offline). Run: python3 scripts/test_e1003_el_mechanical.py
Compliance
- ECSS standards are freely downloadable (ESA); cite the source and paraphrase per standards-map.yaml.
- compliance: STANDARDS-REF, gated: false.
