ECSS Annex A Natural EM Radiation & Indices Reference Data (space-systems/ecss/e1004-annex-a-data)
Use when the task is assembling or checking the natural electromagnetic radiation and solar/geomagnetic activity index reference dataset defined in ECSS-E-ST-10-04C Annex A (normative): the source table that downstream clauses and leaves draw solar-cycle reference values from instead of picking numbers ad hoc.
Domain quick reference
- Annex A is the normative reference-data annex backing clause §6 (electromagnetic radiation) and clause §6.2.2 (solar/geomagnetic activity indices): natural EM radiation quantities (total solar irradiance/TSI, EUV/XUV band irradiance, Earth albedo, Earth IR emission) and activity index reference values (F10.7, its 81-day- smoothed companion F10.7A, and a geomagnetic index such as Ap or Kp) tied to solar-cycle phase.
- Two sibling leaves consume this table rather than re-deriving it:
e1004-em-radiation(§6.2, the EM radiation quantities) ande1004-indices(§6.2.2 + Annex A, the activity index values); any downstream analysis that needs a solar-cycle design case (thermal hot/cold case, power budget, drag viae1004-atmosphere) should trace its numbers back to this leaf's dataset, not to an independently chosen value. - Annex A quantities split into two kinds: phase-dependent quantities (TSI, EUV/XUV irradiance, F10.7, F10.7A, the geomagnetic index) are defined separately per solar-cycle phase (minimum, mean, maximum); phase-independent quantities (Earth albedo, Earth IR emission) are design constants that vary by orbit/season rather than by solar cycle and carry no phase tag.
- A usable dataset entry for a quantity needs a numeric value, a citation back to Annex A, and — for phase-dependent quantities — the correct solar-cycle phase label; an entry missing any of these can't be checked for consistency or safely handed to a downstream leaf.
- Across the three solar-cycle phases, F10.7, F10.7A, the geomagnetic index, TSI, and EUV/XUV irradiance must all be monotonically non-decreasing from minimum to mean to maximum (higher solar activity drives higher radio flux, higher geomagnetic disturbance, and higher irradiance); a violation signals a mis-transcribed or swapped value.
Workflow
- Identify which quantities the current design case needs — the full EM-radiation set, the full index set, or both — and which solar-cycle phase(s) are required (a single phase for a nominal case, minimum+maximum for an envelope/hot-case-cold-case study).
- For each required quantity, record its value, its citation to ECSS-E-ST-10-04C Annex A, and — if the quantity is phase-dependent — the minimum/mean/maximum phase label it belongs to; tag phase-independent quantities (Earth albedo, Earth IR emission) with no solar-cycle phase.
- Check the assembled dataset against the required-quantity list; any quantity absent from the dataset is a missing quantity.
- For each present quantity, check that every entry has a value and a citation, and that phase-dependent quantities only use the minimum/mean/maximum labels while phase-independent quantities only use the phase-independent label — a mismatch here is a phase-tagging error.
- Where a phase-dependent quantity supplies two or more phases, check that its values are ordered minimum ≤ mean ≤ maximum; treat a decrease across phases as an ordering violation to be resolved before use.
- Only mark the dataset complete once every required quantity is
present, every entry passes its value/citation/phase-tagging check,
and every multi-phase quantity passes its ordering check; otherwise
report the specific missing quantities, missing phases, or
violations so
e1004-em-radiationande1004-indicesare not fed bad reference data.
Pitfalls
- Treating an Annex A value as a single fixed constant instead of a solar-cycle-phase-dependent value, so a solar-minimum F10.7 or TSI value gets reused in a solar-maximum worst-case analysis.
- Recording a phase-dependent value without its solar-cycle phase label, which makes the minimum/mean/maximum ordering check impossible to run later.
- Tagging Earth albedo or Earth IR emission with a solar-cycle phase when Annex A ties them to orbit/season instead, which creates a spurious ordering expectation that doesn't apply to those quantities.
- Supplying only the mean-phase value when the actual design case needs an envelope (e.g. a thermal hot-case/cold-case study needs minimum and maximum, not just mean).
- Conflating F10.7 (instantaneous/daily) with F10.7A (81-day-smoothed) as if they were the same index — they are distinct quantities feeding different downstream models.
Behavior contract (gate 3)
The quantity classification, entry validation, phase-tagging check, and multi-phase ordering logic is exercised by the gate 3 contract test: scripts/test_e1004_annex_a_data.py against scripts/e1004_annex_a_data_logic.py (stdlib unittest, offline). Run: python3 scripts/test_e1004_annex_a_data.py
Compliance
- ECSS standards are freely downloadable (ESA); cite the source and paraphrase per standards-map.yaml.
- compliance: STANDARDS-REF, gated: false.
