ECSS Radiation Effects — Displacement Damage Parametric Degradation (space-systems/ecss/e1012-dd-degradation)
Use when the task is predicting how a component's key electrical or optical
parameter degrades over mission life due to displacement damage, following
the procedure in ECSS-E-ST-10-12C §8.6. The workflow covers: selecting a
degradation curve model for the part, computing the end-of-life (EOL)
normalized parameter value, applying the required design margin, and checking
that the margin-adjusted value still satisfies the circuit minimum requirement.
Domain quick reference
- Displacement damage (DD) is caused by non-ionizing radiation (primarily
protons, neutrons, and heavy ions) displacing lattice atoms, degrading
carrier lifetime, mobility, and quantum efficiency in sensitive device types
such as solar cells, bipolar transistors, CCDs, and optocouplers.
- The severity is quantified by the displacement damage dose (DDD), typically
expressed in MeV/g (silicon equivalent) or as equivalent fluence. DDD is
accumulated over the mission duration at the shielded device location and
is the primary driver for selecting points along the parametric degradation
curve.
- Three model forms cover the range of available data: power-law
(P_eol/P_0 = 1 − α·DDD^β), exponential (P_eol/P_0 = exp(−k·DDD)), and
tabular (linear interpolation through manufacturer- or test-derived
data points). The power-law and exponential forms require at least two
curve-fit coefficients traceable to a characterized lot or irradiation
dataset; the tabular form requires a minimum of two (DDD, fraction) pairs
spanning the expected dose range.
- Design margin is applied multiplicatively: the margin-adjusted EOL fraction
equals the computed degraded fraction divided by the margin factor (factor
1 is conservative). ECSS-E-ST-10-12C §8.6 mandates a specific radiation
design margin (RDM); the required value depends on the component category
and lot characterization status — use the applicable RDM table entry rather
than a default.
- The minimum acceptable fraction (min_fraction) is the ratio of the
circuit-required parameter floor to the begin-of-life (BOL) nominal value;
it must be derived from the functional requirement, not assumed.
Workflow
- For each component subject to a DD degradation requirement, retrieve the
accumulated DDD at its shielded location from the environment analysis
(ECSS-E-ST-10-12C §6 or the mission radiation environment specification).
Record the DDD value and its units; mismatched units (e.g. MeV/g vs. p/cm²)
are a common source of error and must be resolved before proceeding.
- Identify the degradation curve model type (power-law, exponential, or
tabular) that is on record for the part lot. If no characterized curve
exists, raise a finding before continuing — applying an uncharacterized
model produces unreliable results.
- Compute the normalized EOL parameter value P_eol/P_0 using the selected
model and the DDD:
- Power-law: P_eol/P_0 = 1 − α·DDD^β (coefficients α, β from the curve fit)
- Exponential: P_eol/P_0 = exp(−k·DDD) (coefficient k from the curve fit)
- Tabular: linear interpolation between the two bracketing (DDD, fraction)
data points; reject a DDD that falls outside the characterized range.
- Apply the radiation design margin: margin-adjusted fraction =
(P_eol/P_0) / RDM_factor. Use the margin factor from the applicable
ECSS-E-ST-10-12C §8 RDM table entry for the component category.
- Compare the margin-adjusted fraction to the circuit minimum fraction
(min_fraction). If margin-adjusted fraction < min_fraction, record a
non-compliance finding identifying the component, its DDD, the computed
fraction, and the shortfall.
- Aggregate findings across all components; a component with no finding on
record passes the DD degradation gate. Components with findings require
a design response (increased shielding, part substitution, derating
reanalysis, or waiver).
Pitfalls
- Omitting the margin step and comparing the raw degraded fraction to
min_fraction — this appears to pass cases that the RDM requirement would
reject; the margin-adjusted value must be used for the compliance check.
- Using a tabular curve's first or last data point as a default when the DDD
falls outside the table range — extrapolation is not valid; the out-of-range
condition must be flagged and the curve extended with additional test data
before the assessment can proceed.
- Applying generic lot-average coefficients to a part procured from a
different lot or process split — each lot should have its own characterized
curve; mixing lots without explicit justification introduces unquantified
uncertainty.
- Deriving min_fraction from the BOL measured value rather than the BOL
nominal (or worst-case) specification — using a high measured value makes
min_fraction appear easier to meet and conceals a potential shortfall on
units with lower BOL values.
- Treating P_eol/P_0 < 0 (power-law with large DDD) as a negligible numerical
artefact — a negative computed fraction signals that the dose exceeds the
model's valid range; flag and stop rather than saturating at zero.
Behavior contract (gate 3)
The degradation model selection, EOL fraction computation, margin application,
and compliance check logic is exercised by the gate 3 contract test:
scripts/test_e1012_dd_degradation.py against
scripts/e1012_dd_degradation_logic.py (stdlib unittest, offline). Run:
python3 scripts/test_e1012_dd_degradation.py
Compliance
- ECSS standards are freely downloadable (ESA); cite the source and paraphrase
per standards-map.yaml.
- compliance: STANDARDS-REF, gated: false.
1---2name: e1012-dd-degradation3description: "Use when determine the end-of-life parametric degradation of a4 component exposed to displacement damage dose under ECSS-E-ST-10-12C §8.6:5 select the degradation curve model (power-law, exponential, or tabular) for6 the part, compute the normalized EOL parameter value from the displacement7 damage dose and curve coefficients, apply the design margin, and verify the8 margin-adjusted EOL value meets the circuit minimum requirement. Flag any9 component whose degradation curve is not on record or whose dose falls outside10 the characterized range. Trigger: ecss, e-st-10-12c, displacement-damage,11 dd-degradation, parametric-degradation, non-ionizing, eol-parameter,12 ddd-curve, bipolar-degradation."13license: Apache-2.014compliance: STANDARDS-REF15standards:16 - id: ecss17 reference-only: true18gated: false19domain: space-systems20pack: space-systems21compatibility: "agentskills.io SKILL.md; any SKILL.md host (Claude Code, Hermes, OpenClaw)"22metadata:23 source: https://skillmd.com/skills/ashfordeou/e1012-dd-degradation24 domain: space-systems25 subdomain: ecss26 tags: [ecss, e-st-10-12c, displacement-damage, dd-degradation, parametric-degradation, non-ionizing, eol-parameter, ddd-curve, bipolar-degradation]27 version: 0.1.028 author: Aero Agent Skills29---3031# ECSS Radiation Effects — Displacement Damage Parametric Degradation (space-systems/ecss/e1012-dd-degradation)3233Use when the task is predicting how a component's key electrical or optical34parameter degrades over mission life due to displacement damage, following35the procedure in ECSS-E-ST-10-12C §8.6. The workflow covers: selecting a36degradation curve model for the part, computing the end-of-life (EOL)37normalized parameter value, applying the required design margin, and checking38that the margin-adjusted value still satisfies the circuit minimum requirement.3940## Domain quick reference4142- Displacement damage (DD) is caused by non-ionizing radiation (primarily43 protons, neutrons, and heavy ions) displacing lattice atoms, degrading44 carrier lifetime, mobility, and quantum efficiency in sensitive device types45 such as solar cells, bipolar transistors, CCDs, and optocouplers.46- The severity is quantified by the displacement damage dose (DDD), typically47 expressed in MeV/g (silicon equivalent) or as equivalent fluence. DDD is48 accumulated over the mission duration at the shielded device location and49 is the primary driver for selecting points along the parametric degradation50 curve.51- Three model forms cover the range of available data: power-law52 (P_eol/P_0 = 1 − α·DDD^β), exponential (P_eol/P_0 = exp(−k·DDD)), and53 tabular (linear interpolation through manufacturer- or test-derived54 data points). The power-law and exponential forms require at least two55 curve-fit coefficients traceable to a characterized lot or irradiation56 dataset; the tabular form requires a minimum of two (DDD, fraction) pairs57 spanning the expected dose range.58- Design margin is applied multiplicatively: the margin-adjusted EOL fraction59 equals the computed degraded fraction divided by the margin factor (factor60 > 1 is conservative). ECSS-E-ST-10-12C §8.6 mandates a specific radiation61 design margin (RDM); the required value depends on the component category62 and lot characterization status — use the applicable RDM table entry rather63 than a default.64- The minimum acceptable fraction (min_fraction) is the ratio of the65 circuit-required parameter floor to the begin-of-life (BOL) nominal value;66 it must be derived from the functional requirement, not assumed.6768## Workflow69701. For each component subject to a DD degradation requirement, retrieve the71 accumulated DDD at its shielded location from the environment analysis72 (ECSS-E-ST-10-12C §6 or the mission radiation environment specification).73 Record the DDD value and its units; mismatched units (e.g. MeV/g vs. p/cm²)74 are a common source of error and must be resolved before proceeding.752. Identify the degradation curve model type (power-law, exponential, or76 tabular) that is on record for the part lot. If no characterized curve77 exists, raise a finding before continuing — applying an uncharacterized78 model produces unreliable results.793. Compute the normalized EOL parameter value P_eol/P_0 using the selected80 model and the DDD:81 - Power-law: P_eol/P_0 = 1 − α·DDD^β (coefficients α, β from the curve fit)82 - Exponential: P_eol/P_0 = exp(−k·DDD) (coefficient k from the curve fit)83 - Tabular: linear interpolation between the two bracketing (DDD, fraction)84 data points; reject a DDD that falls outside the characterized range.854. Apply the radiation design margin: margin-adjusted fraction =86 (P_eol/P_0) / RDM_factor. Use the margin factor from the applicable87 ECSS-E-ST-10-12C §8 RDM table entry for the component category.885. Compare the margin-adjusted fraction to the circuit minimum fraction89 (min_fraction). If margin-adjusted fraction < min_fraction, record a90 non-compliance finding identifying the component, its DDD, the computed91 fraction, and the shortfall.926. Aggregate findings across all components; a component with no finding on93 record passes the DD degradation gate. Components with findings require94 a design response (increased shielding, part substitution, derating95 reanalysis, or waiver).9697## Pitfalls9899- Omitting the margin step and comparing the raw degraded fraction to100 min_fraction — this appears to pass cases that the RDM requirement would101 reject; the margin-adjusted value must be used for the compliance check.102- Using a tabular curve's first or last data point as a default when the DDD103 falls outside the table range — extrapolation is not valid; the out-of-range104 condition must be flagged and the curve extended with additional test data105 before the assessment can proceed.106- Applying generic lot-average coefficients to a part procured from a107 different lot or process split — each lot should have its own characterized108 curve; mixing lots without explicit justification introduces unquantified109 uncertainty.110- Deriving min_fraction from the BOL measured value rather than the BOL111 nominal (or worst-case) specification — using a high measured value makes112 min_fraction appear easier to meet and conceals a potential shortfall on113 units with lower BOL values.114- Treating P_eol/P_0 < 0 (power-law with large DDD) as a negligible numerical115 artefact — a negative computed fraction signals that the dose exceeds the116 model's valid range; flag and stop rather than saturating at zero.117118## Behavior contract (gate 3)119120The degradation model selection, EOL fraction computation, margin application,121and compliance check logic is exercised by the gate 3 contract test:122scripts/test_e1012_dd_degradation.py against123scripts/e1012_dd_degradation_logic.py (stdlib unittest, offline). Run:124python3 scripts/test_e1012_dd_degradation.py125126## Compliance127128- ECSS standards are freely downloadable (ESA); cite the source and paraphrase129 per standards-map.yaml.130- compliance: STANDARDS-REF, gated: false.