ECSS Photovoltaic — Bare Cell Bus Bar and Grid Continuity (space-systems/ecss/e2008-bare-cell-bus-bar-grids)
Use when the task is the front metallization requirement of ECSS-E-ST-20-08C clause 7.5.1.5.3 -- the bus bars and the grid lines of a bare cell have to run through without a break -- turned into a survey that separates what is refused on presence from what is measured, and closes with a disposition.
Domain quick reference
- The front grid is the cell's current collector. Fingers gather from the illuminated surface and deliver into the bus bars; the bus bars carry the whole cell out to the interconnectors. A requirement that the lines run through is a requirement about that path, not about cosmetic appearance.
- The survey has two halves and they must not be run with the same rule. A full interruption or a fracture that separates the metal is decided by presence: there is no width below which a break passes, because what is gone is the path. A narrowing, an edge nick or a void inside the line footprint leaves metal behind and is decided by measurement.
- A narrowing is graded on what survived, not on what was lost. The residual width fraction is the narrowest surviving width over the nominal line width, so two lines of different nominal width with the same absolute loss are correctly different findings.
- A bus bar is held tighter than a finger. Everything the cell collects passes through the bus bar, while a finger carries only its own strip, so the same residual fraction is an accept on one and a non-conformance on the other.
- Width is not the whole screen. Metal that survived still has to carry the line current, so the second axis is the current density in the surviving cross section. A narrowing can sit inside the width band and still drive the density past its limit, and a survey that measures only width will not see it.
- A break is sized as well as refused. The orphaned collection share is the part of a line's strip cut off from any bus bar: everything past the break on a line fed from one end, and nothing at all on a line fed from both, because the far end still delivers. That number tells a reviewer what the cell lost. It never turns the break into an accept.
- A bare cell front grid is not reworkable the way a solder joint is, so the middle disposition holds the cell for a non-conformance decision rather than promising a repair.
- A clean front still produces a record. The survey is the evidence, and an absent record is not the same as an absent break.
Workflow
- Open the survey against a cell identifier. A record with no traceable identifier cannot be dispositioned, because the non-conformance has nothing to attach to.
- Categorize every indication by kind and by the line it sits on. Reject an unrecognized kind or line rather than defaulting it to a neighbouring one and inheriting a limit that does not apply.
- Route each indication to the half that governs it: presence for a break or a crack through, measurement for a narrowing, an edge nick or a void.
- For a break, take the line length, the break position and the number of ends fed from a bus bar, and report the orphaned collection share alongside the refusal.
- For a narrowing, take the narrowest surviving width against the nominal and disposition on the residual width fraction for that line kind.
- Where the line current and the metal thickness are both recorded, take the current density in the surviving cross section and let the worse of the two axes govern. Refuse a half-recorded pair rather than dropping the second axis in silence.
- Close with the cell verdict, the broken lines listed apart, the worst orphaned share, and the non-conformance a review verdict raises.
Pitfalls
- Grading a break by how wide it is. The finding is the loss of the path; a narrow break is still a break and no fraction reaches it.
- Reading a zero orphaned share as a reprieve. A line fed from both ends loses no collection to a single break, and the break is still refused because the second break has nowhere left to go.
- Grading a narrowing on absolute metal lost. The same loss on a wide bus bar and a fine finger are different findings, and only the residual fraction separates them.
- Applying the finger limit to a bus bar. The bus bar carries the whole cell, and the limit that governs it is the tightened one.
- Measuring width and stopping. A narrowing inside the width band can still put the surviving cross section past its current density, and a width-only survey passes it.
- Recording a line current with no metal thickness. The pair produces the density; one without the other silently drops half the screen, so it is refused instead.
- Comparing a residual fraction with its limit by bare arithmetic. The fraction is a quotient and the density is a quotient of a quotient, so a measurement meant to sit exactly on a limit can evaluate a few units in the last place to either side; the comparison absorbs that representation error while the limit stays untouched.
Behavior contract (gate 3)
The presence-versus-measurement split, the residual width fraction, the orphaned collection share, the surviving-cross-section current density and the cell rollup are exercised by the gate 3 contract test: scripts/test_e2008_bare_cell_bus_bar_grids.py against scripts/e2008_bare_cell_bus_bar_grids_logic.py (stdlib unittest, offline). Run: python3 scripts/test_e2008_bare_cell_bus_bar_grids.py
Compliance
- ECSS standards are freely downloadable (ESA); cite the source and paraphrase per standards-map.yaml.
- compliance: STANDARDS-REF, gated: false.
