ECSS Photovoltaic -- Bare Cell Flatness Test (space-systems/ecss/e2008-bare-cell-flatness-test)
Use when the task is clause 7.5.19 of ECSS-E-ST-20-08C: how flat the surface of an unmounted bare solar cell remains over its full area. This leaf reads one cell outline and the height grid measured on it, and returns the deviation from a fitted datum, the shape that deviation takes, and the verdict against the governing allowance.
Domain quick reference
- Coverage is decided before flatness, because a grid that sampled the middle of the cell has measured the middle of the cell. Anything it reports is a lower bound on the real departure, and a lower bound presented as a result is the quietest way this measurement goes wrong. Span in both directions and a reading in every quadrant are what makes the number a full-area number.
- The datum is fitted, not assumed. A perfectly flat cell resting at a slight angle in its fixture reads as a sloped surface, and judged against the bench it fails on tilt that belongs to the setup. The least-squares plane through the readings themselves removes exactly that and nothing else.
- Tilt is still worth reporting once it is removed. A large fitted gradient says the cell was not seated the way the method intended, which is a comment on the measurement rather than on the cell, and it is unrecoverable from the deviation alone.
- Peak-to-valley and RMS answer different questions. Peak-to-valley is the worst gap the cell has to close against its substrate; RMS says whether that gap is one local feature or the whole face.
- Shape is not a refinement of size. A domed cell touches its substrate in the middle and lifts at the corners; a dished one does the opposite and traps adhesive; a buckled one does neither predictably. Two cells with the same peak-to-valley behave differently on bonding, so the centre of the face is compared against its perimeter.
- The allowance has two statements and the tighter one governs. An absolute figure written for a small cell would quietly loosen on a larger one if the diagonal share were not applied beside it, and the reverse on a small cell, so the limit is derived per outline.
- The sense is a ceiling -- less departure is better -- so a cell landing exactly on the allowance is admissible, and the comparison tolerance exists to absorb representation error rather than to widen the limit.
- A cell is thin and free here. It is unmounted precisely so the wafer's own shape is what gets measured, so the support arrangement and the method belong with the result; a flatness figure with no method recorded cannot be compared with the next lot's.
Workflow
- Validate the criteria set first: the absolute allowance, the diagonal share, the review factor, the marginal band, and what the grid must do to count as full-area. A share above one, or a review factor below one, is refused rather than used.
- Resolve the cell outline and derive the diagonal and face area from it. The governing allowance comes from that diagonal, not from a figure typed in beside it.
- Read the height grid back: every station on the cell, no station measured twice, every height finite. An empty grid is refused rather than reported as a flat cell.
- Take coverage: station count, span in both directions as a share of the outline, and a reading in each of the four quadrants. A gap here closes the assessment on flatness not established, before any arithmetic that would look like an answer.
- Fit the least-squares reference plane, refusing a collinear station set that determines no plane, and report the gradient it absorbed as the fixture tilt across the diagonal.
- Profile the residuals: peak-to-valley, the one-sided extremes and RMS, then name the shape from the centre stations against the outer ones, leaving it unnamed when the difference is inside the signature band.
- Compare the peak-to-valley against the governing allowance with a tie admissible, escalate through the review band, and close on one verdict: flatness not established, within limit, referred for review, or exceeds the limit. Report the margin and raise an advisory for an accepted cell inside the marginal band.
Pitfalls
- Measuring a convenient patch and calling it flatness. The clause asks about the full area, and an unsampled quadrant cannot be reported flat.
- Judging the readings against the bench. A tilted seat makes a flat cell fail and no amount of care in the probe recovers it; the datum has to come from the readings.
- Throwing the fitted tilt away after removing it. It is the evidence that the cell was seated as the method intended, and it is gone from the deviation by construction.
- Reporting peak-to-valley alone. The same figure describes a dome, a dish and a local bump, and those three do different things when the cell is bonded down.
- Carrying one absolute allowance across cell sizes. A limit written for a small cell is loose on a large one, which is why the diagonal share sits beside it and the tighter of the two governs.
- Comparing a reading against a derived allowance by bare arithmetic. The limit is a product of a share and a measured dimension, so a reading exactly on it can evaluate a few units in the last place above it; the comparison absorbs that while the allowance stays untouched.
- Recording a flatness figure with no method beside it. The support arrangement changes what a free wafer does, so the number is not comparable with the next lot's without it.
Behavior contract (gate 3)
The criteria validation, the outline and diagonal derivation, the height grid read-back, the full-area coverage test, the least-squares reference plane with its degenerate-grid refusal, the fixture tilt report, the peak-to-valley, one-sided and RMS residual profile, the convex, concave and irregular shape call, the governing allowance selection and the flatness verdict with its margin and marginal advisory are exercised by the gate 3 contract test: scripts/test_e2008_bare_cell_flatness_test.py against scripts/e2008_bare_cell_flatness_test_logic.py (stdlib unittest, offline). Run: python3 scripts/test_e2008_bare_cell_flatness_test.py
Compliance
- ECSS standards are freely downloadable (ESA); cite the source and paraphrase per standards-map.yaml.
- compliance: STANDARDS-REF, gated: false.
