ECSS Photovoltaic — Coverglass Edge Chips (space-systems/ecss/e2008-coverglass-edge-chips)
Use when the task is clause 8.7.1.3.4 of ECSS-E-ST-20-08C: how far a chip on the edge of a coverglass may project inward across the face of the glass. This leaf reads one coverglass outline and the edge chips observed on it, and returns a disposition per chip plus the accumulation rollup that decides the glass.
Domain quick reference
- Inward projection is the graded dimension, not length along the edge. A quarter of a millimetre is the ceiling, and it is a ceiling on reach across the face because that is the direction in which a chip takes cover off the cell.
- The overhang is the second, harder bound and it is read from the drawing rather than typed in. A coverglass sits over its cell with a small margin, so the first fraction of a millimetre of projection eats overhang and nothing else. A glass laid out with less overhang tightens its own limit without anyone editing a table.
- Past the overhang the chip is standing over the illuminated aperture. That is a different failure from an oversized chip: the cell is shaded, the adhesive bond line is open to ultraviolet, and the junction is without the radiation cover the glass exists to provide.
- Run along the edge is bounded separately and more loosely. It decides how much of the sealing edge is now a stress raiser, not how much cover is gone, so it is a share of the edge the chip sits on rather than one number for the glass.
- The run allowance scales with that edge. A three millimetre chip is a small mark on a long edge and a substantial loss on a short one.
- A chip whose span reaches either end of its edge takes a corner and is not this clause's work. It is routed on, because the corner allowance is written on the hypotenuse across the corner and grading it here would apply the wrong limit to it.
- Small accepted chips still accumulate. Cumulative face area, cumulative run against the perimeter, a count per edge and a count per glass catch the coverglass that passed every individual limit and is nevertheless chewed around its outline.
- Two chips near each other are worse than their sum, because the ligament between them carries the load both of them shed.
Workflow
- Resolve the outline: glass length and width, thickness and the overhang, and derive the perimeter, the face area and the illuminated aperture from them. Reject an overhang that leaves no aperture.
- Place each chip on its edge from its start position and its run. Reject a span that does not fit the edge, then decide from whether the span reaches an end whether the chip takes a corner.
- Route a corner-taking chip to the corner clause instead of grading its projection against an edge allowance.
- Grade inward projection against the quarter millimetre ceiling, then against the overhang, so a chip past the ceiling but still inside the overhang is referred and one over the aperture is rejected.
- Bound the run as a share of the edge it sits on, with its own review band above that share.
- Accumulate: face area lost, run against the perimeter, chips per edge, chips per glass, and pairs of chips inside the separation rule.
- Take the worst disposition, escalate on any accumulation finding, and return the glass verdict with the chips that are not accepted named.
Pitfalls
- Grading the chip on how long it runs along the edge. Length along the edge is the visible dimension and the wrong one; the clause is written on reach across the face.
- Treating a quarter of a millimetre as the only bound. On a glass with a thin overhang a chip inside the ceiling can already be standing over the aperture, and only the derived bound reports that.
- Typing the overhang in as a constant. It is a property of this layout, and a narrower one has to tighten the limit by itself.
- Grading a corner-taking chip here. Its allowance is written on the hypotenuse across the corner, so an edge projection test passes chips the corner clause would not.
- Accepting a glass because every chip passed. The cumulative area, run, count and separation allowances exist for exactly that case.
- Screening chips one at a time and never comparing their positions. Two chips separated by a thin ligament are one weak section of edge.
- Measuring the area of a chip as a rectangle. A conchoidal bite tapers to nothing where it meets sound glass, and a rectangle roughly doubles the accumulated area.
- Comparing a measurement with a derived allowance by bare arithmetic. Several allowances here are a product of a criteria share and a measured dimension, so a measurement exactly on one can evaluate a few units in the last place above it; the comparison absorbs that representation error while the allowance stays untouched.
Behavior contract (gate 3)
The outline resolution, the corner-taking span test and its routing, the quarter millimetre projection ceiling, the derived overhang bound and the aperture encroachment it yields, the run band against the edge, the triangular face area model and the cumulative area, perimeter, count and separation rollups with the glass verdict are exercised by the gate 3 contract test: scripts/test_e2008_coverglass_edge_chips.py against scripts/e2008_coverglass_edge_chips_logic.py (stdlib unittest, offline). Run: python3 scripts/test_e2008_coverglass_edge_chips.py
Compliance
- ECSS standards are freely downloadable (ESA); cite the source and paraphrase per standards-map.yaml.
- compliance: STANDARDS-REF, gated: false.
