ECSS Mechanisms — Gear Design (space-systems/ecss/e3301-gear-design)
Use when the task is the gear design of ECSS-E-ST-33-01C clause 4.7.5.4.7 -- showing that a mesh inside a space mechanism carries its torque without breaking a tooth or pitting a flank, keeps a positive and bounded backlash over the whole thermal range, sits in a lubricant it is compatible with, and does all of that for the required number of tooth load cycles.
Domain quick reference
- A gear mesh has two independent strength checks, not one. Tooth bending is a root-fillet stress that scales linearly with tooth force; flank durability is a Hertzian contact stress that scales with the square root of it. A change that fixes one -- a finer module, a wider face, a different material -- moves the other by a different amount, so both are recomputed after every change.
- The Lewis form factor is a function of tooth count, and it falls sharply below about twenty teeth. A pinion chosen small to fit a packaging envelope pays for it twice: fewer teeth carry the same torque at a smaller pitch diameter, and each of those teeth is intrinsically weaker in bending.
- Flank contact stress carries the elastic coefficient of the material pair. A steel pinion running on a polymer wheel is a far softer contact than steel on steel, which lowers the stress and lowers the allowable much further; the pairing is assessed as a pair.
- Allowables are quoted at a reference life. Above it they are derated on a Woehler slope; below it no credit is taken, because a short-life mechanism does not get a stronger material.
- Backlash is a thermal quantity. The centre distance moves with the difference between the gear expansion and the housing expansion, and that motion appears at the mesh multiplied by twice the tangent of the pressure angle. A steel mesh in an aluminium housing loses backlash cold and gains it hot, so both extremes are checked against a floor above zero and a bound above the nominal.
- Lubricant selection is three checks at once: the qualification temperature range against the lubricant rating, the flank contact stress against the load the film is credited to, and the gear material against what the lubricant may sit on. A dry film that needs a metallic substrate and a grease that degrades on fresh steel under boundary conditions both fail on the third check, not the first.
Workflow
- Validate the mesh: module, pinion and wheel tooth counts, face width and transmitted torque, and both materials. A tooth count below the tabulated form-factor range is an input error, not a value to extrapolate.
- Derive the pitch diameters, the centre distance and the tangential tooth force at the pinion pitch circle.
- Compute the Lewis bending stress with the form factor of the pinion tooth count and the dynamic factor of the drive.
- Compute the elastic coefficient of the material pair and from it the flank contact stress at the same tooth force.
- Derate both allowables for the required tooth load cycles and compare each stress against its derated allowable, absorbing representation error at the boundary with a named tolerance.
- Sweep the backlash across the cold case, the assembly temperature and the hot case; hold the minimum above the floor and, when a bound is specified, the maximum below it.
- Run the lubricant against the temperature range, the computed flank stress and the gear material, and return every finding with the numbers that produced it.
Pitfalls
- Sizing on bending alone. A tooth that passes Lewis comfortably can still pit its flank within the mission cycle count, and pitting is the failure mode that shows up in a life test rather than a proof load.
- Taking the backlash measured at assembly as the backlash in orbit. The number that matters is the cold-case minimum with the housing expansion mismatch applied, and it can be a large fraction of the assembled value.
- Checking the cold case only. An oversized hot-case backlash costs pointing accuracy and can let the mesh rattle through a launch vibration case, so the upper bound is a requirement too.
- Applying the life derating below the reference life. It is a knockdown above the reference, never a credit below it; a short-life mechanism keeps the tabulated allowable and no more.
- Choosing a lubricant on temperature range alone. The contact stress the film is credited to, and the substrate the film needs, fail independently of temperature and are the checks most often skipped.
- Reusing a qualified mesh at a higher torque because the stresses still look comfortable. Both allowables depend on the cycle count, so a duty-cycle change re-opens the strength case even when the geometry is untouched.
Behavior contract (gate 3)
The mesh validation, tangential force, Lewis form factor and bending stress, elastic coefficient and flank contact stress, life derating, thermal backlash sweep and lubricant compatibility screen are exercised by the gate 3 contract test: scripts/test_e3301_gear_design.py against scripts/e3301_gear_design_logic.py (stdlib unittest, offline). Run: python3 scripts/test_e3301_gear_design.py
Compliance
- ECSS standards are freely downloadable (ESA); cite the source and paraphrase per standards-map.yaml.
- compliance: STANDARDS-REF, gated: false.
