ECSS Structures — Fluid-Structure Interaction Analysis (space-systems/ecss/fsi-analysis)
Use when the task is to analyze fluid-structure interaction effects in a
spacecraft or launch vehicle per ECSS-E-ST-32 clause 4.6.2.7 — covering
propellant sloshing in tanks, hydroelastic coupling between structural
modes and enclosed fluid volumes, and aerodynamic buffet excitation during
atmospheric flight.
Domain quick reference
- Clause 4.6.2.7 identifies three FSI effect families that must be assessed
for any structure containing fluid or exposed to unsteady aerodynamic
loading: sloshing (propellant or fluid motion inside a tank that exerts
dynamic loads on the tank walls and shifts the vehicle's center of mass),
hydroelastic coupling (interaction between a structural vibration mode and
the inertia of the enclosed fluid, which lowers the effective natural
frequency), and buffet (turbulent boundary-layer pressure fluctuations on
the external skin during launch or atmospheric transit that produce
broadband dynamic loads).
- Sloshing is characterized by its fundamental lateral frequency, which
depends on tank radius, fill level, and effective gravity. The sloshing
fluid can be modeled as an equivalent pendulum whose length is derived from
that frequency. Low fill fractions (below ~30%) and high fill fractions
(above ~85%) both require special attention: partial fill maximizes the
participating sloshing mass at intermediate levels.
- Hydroelastic coupling is significant when the effective sloshing mass
(approximately 63% of the total fluid mass for a cylindrical tank in the
fundamental mode) exceeds roughly 5% of the structural dry mass. When
coupling is significant, the coupled natural frequency is lower than the
dry structural frequency by a factor of 1/sqrt(1 + added-mass ratio), and
the reduced frequency must still satisfy the launcher or mission interface
frequency requirement.
- Buffet loads are estimated from the freestream dynamic pressure, an exposed
reference area, and an empirical buffet pressure coefficient. The resulting
RMS force must be compared against the structural allowable for the affected
panel or component. Buffet is most severe near maximum dynamic pressure
(max-q) during ascent.
Workflow
- Inventory every tank, fluid-wetted volume, and external surface exposed to
unsteady aerodynamic loading. For each tank, record tank inner radius, fill
fraction, fluid density, and structural dry mass. For each external surface,
record the reference area and the dynamic pressure at the critical flight
condition (max-q).
- For each tank, compute the fundamental lateral sloshing frequency using the
cylindrical tank formula (Bessel root chi_11 = 1.8412, effective fluid
height, and tank radius). Derive the equivalent pendulum length from that
frequency and confirm it is consistent with the geometric fill level.
- Compute the effective added sloshing mass using the 63% sloshing-mass
fraction for the fundamental mode of a cylindrical tank. Compute the
added-mass ratio (sloshing mass / structural dry mass). Determine whether
hydroelastic coupling is significant (ratio > 0.05) or negligible.
- Where coupling is significant, compute the coupled natural frequency:
f_coupled = f_dry / sqrt(1 + added-mass ratio). Compute the fractional
frequency shift. Check that f_coupled satisfies the minimum frequency
requirement from the launcher interface control document or mission
requirements; flag any case that fails.
- For each external surface at the critical flight condition, compute the
RMS buffet load: dynamic pressure x reference area x buffet pressure
coefficient. Compare against the structural allowable for that surface;
flag any case that exceeds the allowable.
- Aggregate findings: a structural case is FSI-compliant only when its coupled
frequency margin passes and its buffet load margin passes. Report
non-compliant cases and identify the dominant FSI effect driving the finding.
Pitfalls
- Applying the dry structural frequency to meet frequency requirements without
accounting for the coupled (fluid-loaded) frequency — hydroelastic coupling
can lower the frequency by 10–30% for propellant-heavy configurations, which
may violate launcher interface requirements that appeared to be met.
- Using total fluid mass instead of the participating sloshing mass in the
added-mass ratio — the entire propellant load does not slosh; only the
fraction near the free surface participates, and overestimating this leads to
unnecessarily conservative frequency corrections.
- Ignoring sloshing at high fill fractions under the assumption that "the tank
is nearly full so there is no sloshing" — the sloshing frequency increases at
high fill, but the loads on the tank dome can still be significant and must
be checked.
- Treating buffet as a static load rather than a broadband dynamic excitation —
the RMS load is the starting point; if the buffet spectral content overlaps a
structural mode, dynamic amplification must be included and the peak load can
substantially exceed the RMS value.
Behavior contract (gate 3)
The sloshing frequency, added-mass ratio, hydroelastic coupling determination,
buffet load computation, frequency-shift correction, and margin checks are
exercised by the gate 3 contract test:
scripts/test_fsi_analysis.py against scripts/fsi_analysis_logic.py
(stdlib unittest, offline). Run:
python3 scripts/test_fsi_analysis.py
Compliance
- ECSS standards are freely downloadable (ESA); cite the source and
paraphrase per standards-map.yaml.
- compliance: STANDARDS-REF, gated: false.
1---2name: fsi-analysis3description: "Use when analyze fluid-structure interaction effects in a spacecraft or launch vehicle structural assembly per ECSS-E-ST-32 clause 4.6.2.7: identify sloshing loads from propellant or fluid-filled tank motion, determine hydroelastic coupling between structural vibration modes and enclosed fluid volumes, evaluate aerodynamic buffet excitation during atmospheric flight, compute effective added mass and natural frequency shifts caused by fluid-structure coupling, and verify that combined dynamic responses remain within structural margins. Trigger: ecss, e-st-32-structures-scope, fluid-structure-interaction, sloshing, hydroelastic, buffet, propellant-slosh, fsi, dynamic-coupling, launch-loads."4license: Apache-2.05compliance: STANDARDS-REF6standards:7 - id: ecss8 reference-only: true9gated: false10domain: space-systems11pack: space-systems12compatibility: "agentskills.io SKILL.md; any SKILL.md host (Claude Code, Hermes, OpenClaw)"13metadata:14 source: https://skillmd.com/skills/ashfordeou/fsi-analysis15 domain: space-systems16 subdomain: ecss17 tags: [ecss, e-st-32-structures-scope, fluid-structure-interaction, sloshing, hydroelastic, buffet, propellant-slosh, fsi, dynamic-coupling]18 version: 0.1.019 author: Aero Agent Skills20---2122# ECSS Structures — Fluid-Structure Interaction Analysis (space-systems/ecss/fsi-analysis)2324Use when the task is to analyze fluid-structure interaction effects in a25spacecraft or launch vehicle per ECSS-E-ST-32 clause 4.6.2.7 — covering26propellant sloshing in tanks, hydroelastic coupling between structural27modes and enclosed fluid volumes, and aerodynamic buffet excitation during28atmospheric flight.2930## Domain quick reference3132- Clause 4.6.2.7 identifies three FSI effect families that must be assessed33 for any structure containing fluid or exposed to unsteady aerodynamic34 loading: sloshing (propellant or fluid motion inside a tank that exerts35 dynamic loads on the tank walls and shifts the vehicle's center of mass),36 hydroelastic coupling (interaction between a structural vibration mode and37 the inertia of the enclosed fluid, which lowers the effective natural38 frequency), and buffet (turbulent boundary-layer pressure fluctuations on39 the external skin during launch or atmospheric transit that produce40 broadband dynamic loads).41- Sloshing is characterized by its fundamental lateral frequency, which42 depends on tank radius, fill level, and effective gravity. The sloshing43 fluid can be modeled as an equivalent pendulum whose length is derived from44 that frequency. Low fill fractions (below ~30%) and high fill fractions45 (above ~85%) both require special attention: partial fill maximizes the46 participating sloshing mass at intermediate levels.47- Hydroelastic coupling is significant when the effective sloshing mass48 (approximately 63% of the total fluid mass for a cylindrical tank in the49 fundamental mode) exceeds roughly 5% of the structural dry mass. When50 coupling is significant, the coupled natural frequency is lower than the51 dry structural frequency by a factor of 1/sqrt(1 + added-mass ratio), and52 the reduced frequency must still satisfy the launcher or mission interface53 frequency requirement.54- Buffet loads are estimated from the freestream dynamic pressure, an exposed55 reference area, and an empirical buffet pressure coefficient. The resulting56 RMS force must be compared against the structural allowable for the affected57 panel or component. Buffet is most severe near maximum dynamic pressure58 (max-q) during ascent.5960## Workflow61621. Inventory every tank, fluid-wetted volume, and external surface exposed to63 unsteady aerodynamic loading. For each tank, record tank inner radius, fill64 fraction, fluid density, and structural dry mass. For each external surface,65 record the reference area and the dynamic pressure at the critical flight66 condition (max-q).672. For each tank, compute the fundamental lateral sloshing frequency using the68 cylindrical tank formula (Bessel root chi_11 = 1.8412, effective fluid69 height, and tank radius). Derive the equivalent pendulum length from that70 frequency and confirm it is consistent with the geometric fill level.713. Compute the effective added sloshing mass using the 63% sloshing-mass72 fraction for the fundamental mode of a cylindrical tank. Compute the73 added-mass ratio (sloshing mass / structural dry mass). Determine whether74 hydroelastic coupling is significant (ratio > 0.05) or negligible.754. Where coupling is significant, compute the coupled natural frequency:76 f_coupled = f_dry / sqrt(1 + added-mass ratio). Compute the fractional77 frequency shift. Check that f_coupled satisfies the minimum frequency78 requirement from the launcher interface control document or mission79 requirements; flag any case that fails.805. For each external surface at the critical flight condition, compute the81 RMS buffet load: dynamic pressure x reference area x buffet pressure82 coefficient. Compare against the structural allowable for that surface;83 flag any case that exceeds the allowable.846. Aggregate findings: a structural case is FSI-compliant only when its coupled85 frequency margin passes and its buffet load margin passes. Report86 non-compliant cases and identify the dominant FSI effect driving the finding.8788## Pitfalls8990- Applying the dry structural frequency to meet frequency requirements without91 accounting for the coupled (fluid-loaded) frequency — hydroelastic coupling92 can lower the frequency by 10–30% for propellant-heavy configurations, which93 may violate launcher interface requirements that appeared to be met.94- Using total fluid mass instead of the participating sloshing mass in the95 added-mass ratio — the entire propellant load does not slosh; only the96 fraction near the free surface participates, and overestimating this leads to97 unnecessarily conservative frequency corrections.98- Ignoring sloshing at high fill fractions under the assumption that "the tank99 is nearly full so there is no sloshing" — the sloshing frequency increases at100 high fill, but the loads on the tank dome can still be significant and must101 be checked.102- Treating buffet as a static load rather than a broadband dynamic excitation —103 the RMS load is the starting point; if the buffet spectral content overlaps a104 structural mode, dynamic amplification must be included and the peak load can105 substantially exceed the RMS value.106107## Behavior contract (gate 3)108109The sloshing frequency, added-mass ratio, hydroelastic coupling determination,110buffet load computation, frequency-shift correction, and margin checks are111exercised by the gate 3 contract test:112scripts/test_fsi_analysis.py against scripts/fsi_analysis_logic.py113(stdlib unittest, offline). Run:114python3 scripts/test_fsi_analysis.py115116## Compliance117118- ECSS standards are freely downloadable (ESA); cite the source and119 paraphrase per standards-map.yaml.120- compliance: STANDARDS-REF, gated: false.