ECSS Structures — Material Class Design Rules (space-systems/ecss/material-class-design-rules)
Use when the task is applying the material-class-specific structural design
rules of ECSS-E-ST-32C sections 4.5.9–4.5.12 — covering metallic materials,
non-metallic materials, composite laminates, and adhesive-bonded joints —
to confirm a candidate material or joint configuration is acceptable for
the structural design baseline before drawings are released or analysis
evidence is closed.
Domain quick reference
- ECSS-E-ST-32C §4.5.9–§4.5.12 groups structural materials into four
classes: metal, non-metallic, composite laminate, and adhesive-bonded
joint. Each class carries its own rule set that must be satisfied in
addition to the general strength and stiffness requirements of the
standard.
- For metals (§4.5.9): the rule set covers minimum ductility (elongation
floor), stress-corrosion cracking (SCC) susceptibility screening, and
galvanic-pair compatibility between dissimilar alloys in structural
contact. A ductile failure mode is a prerequisite for the factors-of-safety
regime in E-ST-32C; an SCC-susceptible alloy without a documented
mitigation is a design non-conformance; a galvanic-incompatible pair without
insulating or coating protection risks accelerated corrosion in ground
handling and on-orbit environments.
- For non-metallic materials (§4.5.10): outgassing characterisation per
ECSS-Q-ST-70-02 (TML ≤ 1.0 %, CVCM ≤ 0.1 %) is required to protect
adjacent optical, thermal, and electrical surfaces. Radiation tolerance
must be confirmed for the mission dose level. The operating temperature
envelope must be bounded and on record.
- For composite laminates (§4.5.11): the layup must be symmetric about
its mid-plane and balanced (equal populations of +θ and −θ plies) to
prevent out-of-plane warping and in-plane shear distortion under curing
and thermal loads. Allowable properties must carry a hygrothermal
knockdown factor (wet/hot condition) before comparison with analysis
results. Laminates with a high fraction of 0° plies (above ~80 %) require
a micro-cracking susceptibility assessment under thermal cycling.
- For adhesive-bonded joints (§4.5.12): the bond-line thickness must
fall within the adhesive manufacturer's qualified window (nominally
0.05–0.50 mm); the bond surfaces must be cleaned and primed before
adhesive application; thermal-cycling-induced peel and shear loads must
be included in the joint analysis; and the calculated peel stress must
remain below the system allowable.
Workflow
- Receive the candidate material or joint data sheet and identify its
material class. Reject any material class label that does not map to
one of the four recognized classes before proceeding.
- Metal path (§4.5.9): confirm yield strength, ultimate strength, and
elongation are documented. Flag an elongation below 2 % as a ductility
violation. If the alloy is SCC-susceptible, verify a mitigation measure
(heat treatment, stress relief, protective coating, or alloy substitution)
is on record; absent one, flag a rule violation. List all alloys in
structural contact and check every pair against the galvanic-incompatibility
table; flag any incompatible pair that lacks insulation or protective
coating.
- Non-metallic path (§4.5.10): retrieve TML and CVCM values from the
outgassing test data sheet. Flag an exceedance of either limit. Confirm
radiation qualification evidence covers the design dose level. Confirm
the operational temperature range is documented and bounded.
- Composite path (§4.5.11): retrieve the layup card. Flag an
unsymmetric layup or an unbalanced layup. Confirm the allowables table
carries a hygrothermal knockdown entry; flag its absence. If the fraction
of 0° plies exceeds 0.80, confirm a micro-cracking assessment is on
record; absent one, flag a susceptibility risk.
- Adhesive-bonded path (§4.5.12): confirm the bond-line thickness
specification falls within 0.05–0.50 mm; flag values outside this range.
Confirm cleaning and primer steps are documented in the process card;
flag absent steps. Confirm the joint analysis includes thermal-cycling
loads; flag their absence. Compare calculated peel stress with the
adhesive-system allowable; flag an exceedance.
- Aggregate the findings across all applicable rule checks. The material
or joint is not cleared for the structural baseline until the violation
list is empty.
Pitfalls
- Applying the strength rules from §4.5.3–§4.5.8 but skipping the
material-class rules in §4.5.9–§4.5.12 entirely — both sets are
mandatory; the strength analysis alone does not satisfy the material
design rules.
- Treating an elongation value below 2 % as acceptable because the
ultimate margin is positive — the ductility floor is a separate,
unconditional gate; a brittle failure mode invalidates the
factors-of-safety basis of the strength analysis.
- Omitting the hygrothermal knockdown factor from composite allowables
because the mission environment is "mostly cold" — the knockdown is
applied to the allowable, not derived from a predicted environment; its
absence means the allowables table is non-compliant with §4.5.11
regardless of the thermal prediction.
- Accepting an outgassing test data sheet with TML or CVCM values above
the ECSS-Q-ST-70-02 limits on the grounds that the test article was a
"representative coupon" — only a test article from the same lot and
process can substitute; a coupon from a different batch requires its
own test entry.
- Using the bond-line thickness specification as the process target without
checking that it falls inside the adhesive manufacturer's qualified
window — specifying a thickness the adhesive manufacturer has not
qualified creates a latent design non-conformance even if the measured
thickness satisfies the drawing.
Behavior contract (gate 3)
The material-categorization, metal-rule, non-metallic-rule, composite-rule,
and adhesive-bonded-rule logic is exercised by the gate 3 contract test:
scripts/test_material_class_design_rules.py against
scripts/material_class_design_rules_logic.py (stdlib unittest, offline). Run:
python3 scripts/test_material_class_design_rules.py
Compliance
- ECSS standards are freely downloadable (ESA); cite the source and
paraphrase per standards-map.yaml.
- compliance: STANDARDS-REF, gated: false.
1---2name: material-class-design-rules3description: "Use when determine and enforce material-class design rules for a spacecraft structural element under ECSS-E-ST-32C sections 4.5.9–4.5.12: categorize the element material as metal, non-metallic, composite, or adhesive-bonded; apply the corresponding rule set — ductility floor, stress-corrosion cracking mitigation, and galvanic-pair screening for metals; outgassing budget (TML, CVCM) and radiation tolerance for non-metallics; symmetric/balanced layup, hygrothermal knockdown factor, and micro-crack susceptibility for composites; bond-line thickness, surface preparation, thermal-cycling load, and peel-stress margin for adhesive joints — and report all violations before the material is accepted into the structural design baseline. Trigger: ecss, e-st-32-structures-scope, material-design-rules, metals, non-metallic, composites, adhesive-bonded, galvanic-compatibility, outgassing, hygrothermal."4license: Apache-2.05compliance: STANDARDS-REF6standards:7 - id: ecss8 reference-only: true9gated: false10domain: space-systems11pack: space-systems12compatibility: "agentskills.io SKILL.md; any SKILL.md host (Claude Code, Hermes, OpenClaw)"13metadata:14 source: https://skillmd.com/skills/ashfordeou/material-class-design-rules15 domain: space-systems16 subdomain: ecss17 tags: [ecss, e-st-32-structures-scope, material-design-rules, metals, non-metallic, composites, adhesive-bonded, galvanic-compatibility, outgassing, hygrothermal]18 version: 0.1.019 author: Aero Agent Skills20---2122# ECSS Structures — Material Class Design Rules (space-systems/ecss/material-class-design-rules)2324Use when the task is applying the material-class-specific structural design25rules of ECSS-E-ST-32C sections 4.5.9–4.5.12 — covering metallic materials,26non-metallic materials, composite laminates, and adhesive-bonded joints —27to confirm a candidate material or joint configuration is acceptable for28the structural design baseline before drawings are released or analysis29evidence is closed.3031## Domain quick reference3233- ECSS-E-ST-32C §4.5.9–§4.5.12 groups structural materials into four34 classes: metal, non-metallic, composite laminate, and adhesive-bonded35 joint. Each class carries its own rule set that must be satisfied in36 addition to the general strength and stiffness requirements of the37 standard.38- For **metals (§4.5.9)**: the rule set covers minimum ductility (elongation39 floor), stress-corrosion cracking (SCC) susceptibility screening, and40 galvanic-pair compatibility between dissimilar alloys in structural41 contact. A ductile failure mode is a prerequisite for the factors-of-safety42 regime in E-ST-32C; an SCC-susceptible alloy without a documented43 mitigation is a design non-conformance; a galvanic-incompatible pair without44 insulating or coating protection risks accelerated corrosion in ground45 handling and on-orbit environments.46- For **non-metallic materials (§4.5.10)**: outgassing characterisation per47 ECSS-Q-ST-70-02 (TML ≤ 1.0 %, CVCM ≤ 0.1 %) is required to protect48 adjacent optical, thermal, and electrical surfaces. Radiation tolerance49 must be confirmed for the mission dose level. The operating temperature50 envelope must be bounded and on record.51- For **composite laminates (§4.5.11)**: the layup must be symmetric about52 its mid-plane and balanced (equal populations of +θ and −θ plies) to53 prevent out-of-plane warping and in-plane shear distortion under curing54 and thermal loads. Allowable properties must carry a hygrothermal55 knockdown factor (wet/hot condition) before comparison with analysis56 results. Laminates with a high fraction of 0° plies (above ~80 %) require57 a micro-cracking susceptibility assessment under thermal cycling.58- For **adhesive-bonded joints (§4.5.12)**: the bond-line thickness must59 fall within the adhesive manufacturer's qualified window (nominally60 0.05–0.50 mm); the bond surfaces must be cleaned and primed before61 adhesive application; thermal-cycling-induced peel and shear loads must62 be included in the joint analysis; and the calculated peel stress must63 remain below the system allowable.6465## Workflow66671. Receive the candidate material or joint data sheet and identify its68 material class. Reject any material class label that does not map to69 one of the four recognized classes before proceeding.702. **Metal path (§4.5.9):** confirm yield strength, ultimate strength, and71 elongation are documented. Flag an elongation below 2 % as a ductility72 violation. If the alloy is SCC-susceptible, verify a mitigation measure73 (heat treatment, stress relief, protective coating, or alloy substitution)74 is on record; absent one, flag a rule violation. List all alloys in75 structural contact and check every pair against the galvanic-incompatibility76 table; flag any incompatible pair that lacks insulation or protective77 coating.783. **Non-metallic path (§4.5.10):** retrieve TML and CVCM values from the79 outgassing test data sheet. Flag an exceedance of either limit. Confirm80 radiation qualification evidence covers the design dose level. Confirm81 the operational temperature range is documented and bounded.824. **Composite path (§4.5.11):** retrieve the layup card. Flag an83 unsymmetric layup or an unbalanced layup. Confirm the allowables table84 carries a hygrothermal knockdown entry; flag its absence. If the fraction85 of 0° plies exceeds 0.80, confirm a micro-cracking assessment is on86 record; absent one, flag a susceptibility risk.875. **Adhesive-bonded path (§4.5.12):** confirm the bond-line thickness88 specification falls within 0.05–0.50 mm; flag values outside this range.89 Confirm cleaning and primer steps are documented in the process card;90 flag absent steps. Confirm the joint analysis includes thermal-cycling91 loads; flag their absence. Compare calculated peel stress with the92 adhesive-system allowable; flag an exceedance.936. Aggregate the findings across all applicable rule checks. The material94 or joint is not cleared for the structural baseline until the violation95 list is empty.9697## Pitfalls9899- Applying the strength rules from §4.5.3–§4.5.8 but skipping the100 material-class rules in §4.5.9–§4.5.12 entirely — both sets are101 mandatory; the strength analysis alone does not satisfy the material102 design rules.103- Treating an elongation value below 2 % as acceptable because the104 ultimate margin is positive — the ductility floor is a separate,105 unconditional gate; a brittle failure mode invalidates the106 factors-of-safety basis of the strength analysis.107- Omitting the hygrothermal knockdown factor from composite allowables108 because the mission environment is "mostly cold" — the knockdown is109 applied to the allowable, not derived from a predicted environment; its110 absence means the allowables table is non-compliant with §4.5.11111 regardless of the thermal prediction.112- Accepting an outgassing test data sheet with TML or CVCM values above113 the ECSS-Q-ST-70-02 limits on the grounds that the test article was a114 "representative coupon" — only a test article from the same lot and115 process can substitute; a coupon from a different batch requires its116 own test entry.117- Using the bond-line thickness specification as the process target without118 checking that it falls inside the adhesive manufacturer's qualified119 window — specifying a thickness the adhesive manufacturer has not120 qualified creates a latent design non-conformance even if the measured121 thickness satisfies the drawing.122123## Behavior contract (gate 3)124125The material-categorization, metal-rule, non-metallic-rule, composite-rule,126and adhesive-bonded-rule logic is exercised by the gate 3 contract test:127scripts/test_material_class_design_rules.py against128scripts/material_class_design_rules_logic.py (stdlib unittest, offline). Run:129python3 scripts/test_material_class_design_rules.py130131## Compliance132133- ECSS standards are freely downloadable (ESA); cite the source and134 paraphrase per standards-map.yaml.135- compliance: STANDARDS-REF, gated: false.