ECSS Structures — Pressure Hardware Category Determination (space-systems/ecss/ph-classification)
Use when the task is the pressure hardware category determination required by ECSS-E-ST-32 clause 4.1 — applying the figure 4-1 through 4-3 decision criteria to assign each hardware item to one of the four pressure categories (PV, PS, PC, SPE) and resolving composite assemblies into their constituent category structure.
Domain quick reference
Clause 4.1 establishes four pressure hardware categories. A Pressure Vessel (PV) is a single closed item whose sole primary function is pressure retention; it does not carry primary structural loads beyond those imposed by the pressure itself. A Pressure System (PS) is an interconnected assembly of pressure-retaining components (vessels, pipes, valves, fittings) that work as a functional unit; each constituent item within the PS is categorized individually before the assembly as a whole is resolved to PS. A Pressure Container (PC) is a closed item that retains pressure and simultaneously carries primary structural loads (e.g., a propellant tank that is also a primary structural node of the spacecraft). Simple Pressure Equipment (SPE) is a pressure-retaining item that meets all simplicity criteria simultaneously: simple geometric shape, maximum expected operating pressure (MEOP) at or below the threshold, internal volume at or below the threshold, standard/recognized material, and no internal heat source.
The figure 4-1 decision tree evaluates items in priority order: assembly status first (→ PS), then structural-load concurrency (→ PC), then SPE simplicity criteria (→ SPE), with PV as the default for any item that fails all three branch conditions. Figure 4-2 codifies the SPE simplicity criteria as a five-condition AND gate; failure of any single condition routes the item to PV. Figure 4-3 addresses composite assemblies by decomposing the PS into its constituent items and recursively applying the figure 4-1 logic to each before rolling up to the PS label at the assembly level.
MEOP is the highest pressure a system is expected to experience in service, including all operating modes; it is the governing pressure parameter for the SPE threshold check, not proof pressure or burst pressure.
Workflow
For each hardware item under review, determine whether it is an interconnected assembly of pressure-retaining components forming a functional unit. If yes, record it as a PS candidate and enumerate its constituent sub-items for individual evaluation in the next step.
For each item that is not an assembly (including PS sub-items), check whether it concurrently carries primary structural loads while retaining pressure. If both functions are present, assign PC. Do not apply the SPE or PV checks to a PC candidate.
For items that are neither assemblies nor PC candidates, evaluate the five SPE simplicity criteria simultaneously: (a) geometry is a simple shape (sphere, plain cylinder, or flat-ended cylinder), (b) MEOP does not exceed the SPE pressure threshold, (c) internal volume does not exceed the SPE volume threshold, (d) material is standard and recognized for pressure service, (e) there is no internal heat source. Only if all five conditions are satisfied, assign SPE.
Any item that does not satisfy the assembly, PC, or SPE conditions is assigned PV. Record the rationale — which SPE criterion or criteria were not met — for traceability.
For PS assemblies, record the category of each sub-item alongside the PS category of the assembly. The composite result is the PS label at the top level with the constituent item results nested beneath it.
Confirm that every pressure item in scope has received a category assignment; flag any item whose input data was incomplete (missing MEOP, volume, or structural-load status) as an unresolved item requiring further data before the assessment can close.
Pitfalls
Applying the SPE check to an item that also carries structural loads — the PC branch must be resolved before the SPE gate is reached; an item that carries structural loads is PC regardless of whether it meets the simplicity criteria.
Treating an assembly as a single PV because the assembly as a whole is not simple — the PS category exists specifically to capture assemblies; do not collapse a multi-component pressure circuit into a single PV assessment.
Using proof or burst pressure rather than MEOP for the SPE threshold check — the SPE criteria reference the expected operating pressure, not the test or failure pressure; applying burst pressure will incorrectly exclude items that legitimately qualify as SPE.
Omitting the structural-load question for items that are geometrically simple and low-pressure — a spherical titanium tank that is also a primary spacecraft structural node is PC, not SPE or PV, regardless of its pressure and volume values.
Leaving a sub-item's category blank and rolling the whole assembly up to PS without individual records — figure 4-3 requires that each constituent item be categorized; the PS label at the assembly level does not replace the per-item category records needed for subsequent fracture control and factors-of-safety application.
Behavior contract (gate 3)
The category-determination logic for PV, PS, PC, SPE, the SPE five- condition gate, composite assembly resolution, and input validation are exercised by the gate 3 contract test: scripts/test_ph_classification.py against scripts/ph_classification_logic.py (stdlib unittest, offline). Run: python3 scripts/test_ph_classification.py
Compliance
- ECSS standards are freely downloadable (ESA); cite the source and paraphrase per standards-map.yaml.
- compliance: STANDARDS-REF, gated: false.
