ECSS Harness Manufacturing — Complementary EMC Shielding with Conductive Foil (space-systems/ecss/q2030-comp-emc-foil)
Use when the task is the complementary foil-shielding layer of
ECSS-Q-ST-20-30C clause 7.8 -- applying a conductive metal foil as an EMC
shield over a harness and terminating it, on top of the shielding
workmanship the standard delegates to its adopted chapter.
Domain quick reference
- Foil is chosen where braid cannot go: it gives close to full coverage
at almost no mass, it wraps a bundle no braid will slide over, and it
has no apertures of its own. What it does not give is strength,
handling tolerance or a way out, which is where every foil requirement
comes from.
- Thickness is set by physics, not by handling. A shield thinner than the
skin depth of its metal at the lowest frequency of concern passes field
rather than reflecting and absorbing it, so the thickness is graded
against a computed skin depth and the number of skin depths the project
demands -- and the skin depth grows as the frequency falls, so the
low-frequency end is what sizes the foil.
- Application geometry is arithmetic. A helically wrapped tape advances
by its width less its overlap, so the overlap fraction alone fixes both
the pitch and how many foil layers sit over any point. An overlap of a
half gives two layers everywhere; a quarter gives less than one and a
half, and the thin places are where the shield fails.
- Foil tape is not symmetric. The conductive layer sits on a carrier
film, so a tape wound the wrong way round puts an insulator against the
drain wire: the shield looks perfect, measures open, and the defect is
invisible once the outer covering is on.
- Foil cannot terminate itself. It leaves through a drain wire, and that
drain wire's run between the foil and the backshell is a pigtail whose
inductive reactance rises with frequency. The reactance against the
reference impedance of a full circumferential termination is what the
pigtail costs in decibels, and it is the reason a long drain wire
undoes the shield it was fitted to complete.
Workflow
- Compute the skin depth of the foil metal from its resistivity, its
relative permeability and the lowest frequency the shield is required
to work from.
- Grade the foil thickness against the required number of skin depths,
absorbing an exact equality with a tolerance instead of rounding the
thickness.
- Turn the tape width and overlap fraction into the wrap pitch and the
number of layers over any point, then grade the layer count against
the project requirement.
- Compute the tape length the run consumes from the pitch, the bundle
circumference and the run length, so the estimate that sizes the
material is the same arithmetic the inspection uses.
- Confirm the conductive face is applied inward and that the drain wire
runs continuously against it for the whole run.
- Compute the pigtail inductance from the drain-wire length, its
reactance at the highest frequency of concern, and the decibel penalty
that reactance carries against the reference impedance.
- Grade the penalty against what the project allows, then roll the
application and termination findings into one verdict.
Pitfalls
- Sizing the foil at the highest frequency in the requirement. Skin depth
grows as frequency falls, so the low-frequency end is what sets the
thickness; sizing at the top of the band produces a foil that is thin
where it matters.
- Reading an overlap percentage as a coverage percentage. The overlap
sets the layer count; coverage is complete either way until the layer
count drops below one, at which point there are bare gaps between
turns.
- Treating tape orientation as a handling preference. Carrier-side inward
is an open shield with a perfect appearance, and it is found at the EMC
test after the harness is installed.
- Terminating the foil by folding it back under a clamp. Foil tears and
cold-flows under clamping load; the drain wire exists because the foil
itself is not a terminable conductor.
- Leaving the drain wire long because it is convenient to dress. The
penalty grows with both length and frequency, so a drain wire dressed
for tidiness can cost more shielding than the foil ever provided.
- Quoting one shielding-effectiveness figure for the run. The figure
belongs to the foil; the termination has its own cost, and the run is
only as good as the two together.
- Failing a thickness or a penalty that lands exactly on its bound. The
equality is a representation question, settled with a tolerance inside
the comparison and never by moving the bound.
Behavior contract (gate 3)
The skin-depth computation, the thickness grading, the helical pitch and
layer-count geometry, the tape-length estimate, the conductive-face and
drain-wire continuity checks, the pigtail inductance, reactance and
decibel penalty, and the combined application-plus-termination verdict
are exercised by the gate 3 contract test:
scripts/test_q2030_comp_emc_foil.py against
scripts/q2030_comp_emc_foil_logic.py (stdlib unittest, offline). Run:
python3 scripts/test_q2030_comp_emc_foil.py
Compliance
- ECSS standards are freely downloadable (ESA); cite the source and
paraphrase per standards-map.yaml.
- compliance: STANDARDS-REF, gated: false.
1---2name: q2030-comp-emc-foil3description: "Validate a conductive metal foil EMC shield against the complementary application and termination criteria of ECSS-Q-ST-20-30C clause 7.8. Use when the task is sizing the foil thickness against the skin depth of its metal at the lowest frequency the shield must work from, turning a helical wrap overlap into a pitch, a layer count over every point and the tape length the run consumes, confirming the conductive face is applied inward against the drain wire, and costing the drain-wire pigtail in decibels against a full circumferential termination. Trigger: ecss, q-st-20-30c, conductive-foil-emc-shield, foil-skin-depth-sizing, helical-foil-wrap-overlap, foil-drain-wire-termination, shield-pigtail-penalty-db, conductive-face-orientation, foil-tape-length-estimate."4license: Apache-2.05compliance: STANDARDS-REF6standards:7 - id: ecss8 reference-only: true9gated: false10domain: space-systems11pack: space-systems12compatibility: "agentskills.io SKILL.md; any SKILL.md host (Claude Code, Hermes, OpenClaw)"13metadata:14 source: https://skillmd.com/skills/ashfordeou/q2030-comp-emc-foil15 domain: space-systems16 subdomain: ecss17 tags: [ecss, q-st-20-electrical-harness-scope, q-st-20-30c, q2030-comp-emc-foil, conductive-foil-emc-shield, foil-skin-depth-sizing, helical-foil-wrap-overlap, foil-drain-wire-termination, shield-pigtail-penalty-db]18 version: 0.1.019 author: Aero Agent Skills20---2122# ECSS Harness Manufacturing — Complementary EMC Shielding with Conductive Foil (space-systems/ecss/q2030-comp-emc-foil)2324Use when the task is the complementary foil-shielding layer of25ECSS-Q-ST-20-30C clause 7.8 -- applying a conductive metal foil as an EMC26shield over a harness and terminating it, on top of the shielding27workmanship the standard delegates to its adopted chapter.2829## Domain quick reference3031- Foil is chosen where braid cannot go: it gives close to full coverage32 at almost no mass, it wraps a bundle no braid will slide over, and it33 has no apertures of its own. What it does not give is strength,34 handling tolerance or a way out, which is where every foil requirement35 comes from.36- Thickness is set by physics, not by handling. A shield thinner than the37 skin depth of its metal at the lowest frequency of concern passes field38 rather than reflecting and absorbing it, so the thickness is graded39 against a computed skin depth and the number of skin depths the project40 demands -- and the skin depth grows as the frequency falls, so the41 low-frequency end is what sizes the foil.42- Application geometry is arithmetic. A helically wrapped tape advances43 by its width less its overlap, so the overlap fraction alone fixes both44 the pitch and how many foil layers sit over any point. An overlap of a45 half gives two layers everywhere; a quarter gives less than one and a46 half, and the thin places are where the shield fails.47- Foil tape is not symmetric. The conductive layer sits on a carrier48 film, so a tape wound the wrong way round puts an insulator against the49 drain wire: the shield looks perfect, measures open, and the defect is50 invisible once the outer covering is on.51- Foil cannot terminate itself. It leaves through a drain wire, and that52 drain wire's run between the foil and the backshell is a pigtail whose53 inductive reactance rises with frequency. The reactance against the54 reference impedance of a full circumferential termination is what the55 pigtail costs in decibels, and it is the reason a long drain wire56 undoes the shield it was fitted to complete.5758## Workflow59601. Compute the skin depth of the foil metal from its resistivity, its61 relative permeability and the lowest frequency the shield is required62 to work from.632. Grade the foil thickness against the required number of skin depths,64 absorbing an exact equality with a tolerance instead of rounding the65 thickness.663. Turn the tape width and overlap fraction into the wrap pitch and the67 number of layers over any point, then grade the layer count against68 the project requirement.694. Compute the tape length the run consumes from the pitch, the bundle70 circumference and the run length, so the estimate that sizes the71 material is the same arithmetic the inspection uses.725. Confirm the conductive face is applied inward and that the drain wire73 runs continuously against it for the whole run.746. Compute the pigtail inductance from the drain-wire length, its75 reactance at the highest frequency of concern, and the decibel penalty76 that reactance carries against the reference impedance.777. Grade the penalty against what the project allows, then roll the78 application and termination findings into one verdict.7980## Pitfalls8182- Sizing the foil at the highest frequency in the requirement. Skin depth83 grows as frequency falls, so the low-frequency end is what sets the84 thickness; sizing at the top of the band produces a foil that is thin85 where it matters.86- Reading an overlap percentage as a coverage percentage. The overlap87 sets the layer count; coverage is complete either way until the layer88 count drops below one, at which point there are bare gaps between89 turns.90- Treating tape orientation as a handling preference. Carrier-side inward91 is an open shield with a perfect appearance, and it is found at the EMC92 test after the harness is installed.93- Terminating the foil by folding it back under a clamp. Foil tears and94 cold-flows under clamping load; the drain wire exists because the foil95 itself is not a terminable conductor.96- Leaving the drain wire long because it is convenient to dress. The97 penalty grows with both length and frequency, so a drain wire dressed98 for tidiness can cost more shielding than the foil ever provided.99- Quoting one shielding-effectiveness figure for the run. The figure100 belongs to the foil; the termination has its own cost, and the run is101 only as good as the two together.102- Failing a thickness or a penalty that lands exactly on its bound. The103 equality is a representation question, settled with a tolerance inside104 the comparison and never by moving the bound.105106## Behavior contract (gate 3)107108The skin-depth computation, the thickness grading, the helical pitch and109layer-count geometry, the tape-length estimate, the conductive-face and110drain-wire continuity checks, the pigtail inductance, reactance and111decibel penalty, and the combined application-plus-termination verdict112are exercised by the gate 3 contract test:113scripts/test_q2030_comp_emc_foil.py against114scripts/q2030_comp_emc_foil_logic.py (stdlib unittest, offline). Run:115python3 scripts/test_q2030_comp_emc_foil.py116117## Compliance118119- ECSS standards are freely downloadable (ESA); cite the source and120 paraphrase per standards-map.yaml.121- compliance: STANDARDS-REF, gated: false.