ECSS Harness Manufacturing — Complementary Insulation Sleeving (space-systems/ecss/q2030-comp-sleeving)
Use when the task is the complementary sleeving layer of ECSS-Q-ST-20-30C clause 7.5 -- the space-specific requirements on the insulation sleeving that goes over a terminated contact, on top of the workmanship criteria the standard delegates to its adopted chapter.
Domain quick reference
- A heat-shrinkable sleeve has to satisfy two diameters at once, and they pull in opposite directions. Unshrunk it must clear the largest thing on its assembly path -- usually the contact body or the backshell it was threaded over, not the wire -- and recovered it must close onto the smallest thing it grips. Only a sleeve whose recovery ratio spans both is selectable, which is why an oversize sleeve that slides on easily is so often the wrong one.
- The recovered inside diameter is the supplied bore divided by the recovery ratio, and that is a free-shrink figure. Recovery stops early on anything it grips, so the grip is counted only when the free-shrink diameter sits a named margin below the diameter it has to hold.
- Sleeve length is a cut length, not an installed length. Recovery pulls the sleeve back longitudinally as well as radially, so the cut has to carry the covered span, the overlap owed at each end, and the longitudinal shrinkage on top; a sleeve cut to the installed dimension arrives short and exposes exactly the transition it was there to cover.
- The sleeve also has a place it may not reach. Running it onto the contact's mating face, over its retention or release geometry, or into the connector cavity it would bottom out in turns an insulation part into an assembly defect, so the end position is a dimension with a minimum clearance and not a workmanship impression.
- Sleeving hides what it covers. An opaque sleeve over a joint whose inspection was never separately recorded removes the evidence that the joint was ever inspected, so the opacity is only acceptable against a recorded inspection taken before the sleeve went on.
Workflow
- Validate each sleeve record: an identifier, the supplied bore and recovery ratio, the largest path diameter, the smallest gripped diameter, the covered span, the overlap owed and the cut length.
- Compute the recovered inside diameter, then decide selectability from both directions -- slides on unshrunk, grips once recovered with the named margin -- and report each failure separately so the size change that fixes it is obvious.
- Size the required cut length from the span, both overlaps and the longitudinal shrinkage, and compute what the supplied cut length will actually settle at once it recovers.
- Confirm the installed length still covers the span plus both overlaps, absorbing an exact equality with a tolerance rather than by shaving the overlap.
- Where an end position and a restricted feature are given, compute the clearance between them and grade it against the minimum.
- Where the sleeve is opaque, confirm a separate joint inspection was recorded before it was installed.
- Roll every record up into one verdict with the conforming count and the findings named.
Pitfalls
- Selecting on the recovered diameter alone. A sleeve that grips beautifully may never have passed over the backshell, and that is discovered at the bench with the termination already made.
- Cutting to the installed dimension. Longitudinal shrinkage is not a rounding error on a short sleeve; ignoring it is the usual reason a sleeve ends up a millimetre or two shy of its overlap.
- Treating the overlap as one total rather than one at each end. The overlap is owed on both sides of the transition, so the span carries it twice.
- Running the sleeve up to the contact shoulder because it looks tidier. A sleeve over the retention or release geometry stops the contact seating or stops it ever coming out, and both are found at integration.
- Accepting an opaque sleeve because the joint underneath was "obviously fine". Once covered, the joint has only the record that was made before the sleeve went on; no record means no inspection evidence.
- Failing a sleeve whose installed length lands exactly on the needed length. The equality is a representation question, settled with a tolerance inside the comparison and never by moving the overlap.
- Reusing one sleeve size across a connector because most contacts take it. The path and gripped diameters change with the wire gauge, so a mixed-gauge connector generally needs more than one size.
Behavior contract (gate 3)
The recovered-diameter computation, the slide-on and grip decisions, the selectability verdict, the cut-length sizing with longitudinal shrinkage, the installed-length and span-coverage grading, the restricted-feature clearance and the opaque-sleeve inspectability finding are exercised by the gate 3 contract test: scripts/test_q2030_comp_sleeving.py against scripts/q2030_comp_sleeving_logic.py (stdlib unittest, offline). Run: python3 scripts/test_q2030_comp_sleeving.py
Compliance
- ECSS standards are freely downloadable (ESA); cite the source and paraphrase per standards-map.yaml.
- compliance: STANDARDS-REF, gated: false.
