ECSS Commercial EEE Components -- Class 3 Connectors (space-systems/ecss/q6013-class-3-connectors)
Use when the task is the clause 6.6.6 connector question of ECSS-Q-ST-60-13C at the lowest assurance class: a harness needs a connector family, the contacts that go into it have to come from somewhere, and the question is whether the family that was picked and the parts that were bought hold up as a decision the class can accept.
Domain quick reference
- Two decisions hide inside one word. Choosing the family is a design act, taken from a wire list; sourcing the contacts is a purchasing act, taken from what a distributor had. At this class both are allowed to rest on lighter standing than the classes above accept, which is precisely why each has to be written down rather than assumed.
- A family is admissible or it is not, and the test is arithmetic. Its derated contact current has to cover the worst circuit in the list, its insert has to keep positions free once every circuit is placed, and it has to stand on some recognised specification. A family failing two of those reports two findings, because fixing one leaves the other waiting.
- The allowed contact current is derived, not read. The rated current of one contact is derated for the class and derated again for the share of positions carrying current at once, since an insert with every position loaded heats itself and every contact in it. Applying the loading to the fraction rather than the count keeps one policy working for a nine-way and a sixty-one-way insert.
- Spare positions are the design margin nobody budgets. An insert filled to its last position has no room for the circuit that appears at integration, and by then the family is fixed by every backshell and bracket around it.
- A catalogue-only family is permitted here and the class above does not permit it. That permission is a project decision recorded in policy, not a default nobody voted on, so a project may still declare it insufficient and have the ranking honour that.
- Contact sourcing carries the insert's real quality. A contact from the connector manufacturer inherits the insert's retention and plating basis. A contact from an alternative source may be used at this class where an interchangeability record exists, and it is credited below a manufacturer part because the record covers the dimensions rather than the process behind them.
- An unidentified lot closes the question rather than lowering a score. A contact nobody can name cannot be reordered, compared or replaced, and an insert repaired with one is an insert nobody can account for.
- Evidence is scored, not ticked. A subject may be carried on a supplier declaration at this class, and a declaration is credited below a project record so that a selection documented entirely by what a supplier says about itself cannot read as a documented selection.
Workflow
- Validate the selection policy first: the class derating, the loading slope, the spare position floor, the manufacturer sourcing floor, the alternative source credit and its floor, the declaration credit, the evidence share and credited floors, the marginal band and the catalogue-only decision. A loading slope of one, a credit of zero or one, or a credited floor above the plain one is refused rather than used.
- Validate the harness demand: a reference, a whole positive circuit count and a positive worst-case circuit current. A harness with no reference closes the assessment on selection not declared.
- Validate every candidate family: a reference, a recognised family, a recognised qualification standing, whole positive insert positions and a positive rated contact current. A repeated candidate is refused.
- Take each candidate's loading fraction, loading factor and derated contact allowance, then its current headroom and spare position share, and collect every finding against it rather than the first. Compare with a tolerance that absorbs representation error so a value landing on a bound is admissible.
- Rank the candidates that draw no finding on standing, current headroom and spare positions, breaking a tie on the reference so the ranking repeats, and take the top one. No admissible candidate closes the assessment with every reason reported.
- Validate every contact lot and settle sourcing: name each unidentified lot and each alternative lot with no interchangeability record, check the contacts in hand against the circuits to place, and take the manufacturer share and the credited sourcing against their floors.
- Dispose each required evidence subject as held as a project record, held as a supplier declaration, declared without a record, or absent, then report every failing list in full rather than truncating at the first entry.
- Report the selected family, its allowance, headroom and spare share, the rejected candidates, the sourced count, the manufacturer share and credited sourcing, the evidence share and credited evidence, and raise an advisory for an admissible family inside the marginal band. Close on one verdict: selection not declared, no admissible candidate, contact sourcing not established, contact supply short, contact sourcing credit short, selection evidence short, or selection meets class three scope.
Pitfalls
- Sizing the family on the single-contact rating. That rating describes a connector with one wire in it, and the insert being bought will run with most of its positions live.
- Filling the insert to the last position because the wire list fits today. The circuit that appears at integration then needs a different connector, and the connector is the part every backshell, bracket and harness length was built around.
- Reading a catalogue entry as a specification. It states what the manufacturer currently sells, not what the part is held to, and it can change between two deliveries that carry the same order number.
- Buying contacts on price and fitting them without an interchangeability record. Dimensionally similar is not dimensionally interchangeable, and the difference shows up as a retention failure under vibration rather than on the bench.
- Treating an unidentified lot as a scoring problem. It is a traceability failure: the part cannot be reordered, compared against the insert, or matched to the one that failed.
- Crediting a supplier declaration in full. A declaration is permitted here and it is thinner than a record this project holds, which is what the credit records; a declaration naming no supplier is grouped with the subjects that hold no record at all.
Behavior contract (gate 3)
The policy validation, the harness demand validation, the candidate validation, the loading fraction and factor, the derated contact allowance, the current headroom, the spare position share, the candidate findings, the ranking and its tie-break, the contact lot validation, the unidentified and unsupported lot lists, the sourced count, the manufacturer share, the credited sourcing, the project-record, declaration, unrecorded and absent evidence dispositions, the evidence share, the credited evidence, the marginal advisories and the selection verdict are exercised by the gate 3 contract test: scripts/test_q6013_class_3_connectors.py against scripts/q6013_class_3_connectors_logic.py (stdlib unittest, offline). Run: python3 scripts/test_q6013_class_3_connectors.py
Compliance
- ECSS standards are freely downloadable (ESA); cite the source and paraphrase per standards-map.yaml.
- compliance: STANDARDS-REF, gated: false.
