ECSS Mechanical Testing of Metals -- Tensile Testing (space-systems/ecss/q7045-tensile-testing)
Use when the task is the tension test of the methods clause of
ECSS-Q-ST-70-45: a specimen of declared gauge length has been pulled to
fracture, the load-extension record has been converted to engineering stress
and strain, and the question is which properties the record supports and
which of them have to be reported with a caveat.
Domain quick reference
- Modulus is a fit, not a ratio of two points. It is the least-squares slope
over a declared elastic window, and it only means anything alongside the
quality of that fit; a window that has crept past the knee still returns a
slope, and the slope it returns is too low and looks plausible.
- Proof strength is a crossing, not a sample. The offset line of slope E,
shifted by the offset strain, meets the record inside one segment; the
crossing is interpolated in that segment rather than snapped to whichever
recorded point happens to sit nearest it.
- Ultimate strength is the peak of the engineering curve. On a ductile alloy
the peak sits well before the last point, because necking drops the
engineering stress while the specimen is still extending.
- Elongation and reduction of area come from the broken halves. Crosshead
strain at fracture includes the compliance of the frame and the grips, so
it is a machine property, not a material property.
- A specified minimum is a floor the measured value may sit exactly on. A
property landing on its minimum is compliant, and rejecting it is a defect
of the comparison, not a finding about the material.
Workflow
- Validate the record: every point carries a strain and a stress, neither is
negative, and the strain strictly increases through the whole record.
- Fit the modulus over the declared elastic window, requiring at least three
points inside it, and keep the fit quality beside the slope.
- Build the offset line from that modulus and the offset strain, walk the
record for the segment where the record falls below it, and interpolate
the crossing inside that segment.
- Scan for the peak engineering stress and keep the strain it occurred at,
so uniform elongation is available and necking is visible.
- Reduce the broken halves into elongation after fracture and, when the
fracture section was measured, reduction of area.
- Compare each property against its specified minimum with an inclusive
test, and report the modulus fit quality as a finding when the declared
window was not elastic.
Pitfalls
- Taking the modulus from the first and last point of the window. Two points
always fit a line perfectly and the fit quality that would have exposed the
bad window is then unavailable.
- Reporting the last recorded stress as the ultimate strength. On anything
ductile that is the fracture stress and it understates the material.
- Snapping the proof strength to the nearest sample. On a coarse record that
moves the reported value by tens of megapascals with no trace in the report.
- Using crosshead travel for elongation after fracture. The frame and the
grips are in that number and the specimen is not the only thing that
stretched.
- Treating a property that lands exactly on its specified minimum as a
failure. Floating-point representation of the minimum is what failed, and
the comparison has to absorb it.
Behavior contract (gate 3)
The record validation, least-squares modulus with its fit quality, offset
proof-strength crossing, peak detection, elongation and reduction of area,
and the comparison against specified minima are exercised by the gate 3
contract test: scripts/test_q7045_tensile_testing.py against
scripts/q7045_tensile_testing_logic.py (stdlib unittest, offline). Run:
python3 scripts/test_q7045_tensile_testing.py
Compliance
- ECSS standards are freely downloadable (ESA); cite the source and
paraphrase per standards-map.yaml.
- compliance: STANDARDS-REF, gated: false.
1---2name: q7045-tensile-testing3description: "Compute the tensile properties of a metallic specimen from its stress-strain record. Use when a tension test has been run under ECSS-Q-ST-70-45 and the properties have to be reported: fit the modulus by least squares over a declared elastic window and report the quality of that fit, locate the offset proof strength where the shifted line crosses the record, take the ultimate strength from the peak of the curve rather than its last point, derive elongation and reduction of area from the broken halves, and refuse a record whose strain does not increase. Trigger: ecss, q-st-70-45, metallic-tensile-offset-proof-strength, tensile-ultimate-strength-peak, tensile-elongation-after-fracture, tensile-modulus-least-squares-window, tensile-reduction-of-area."4license: Apache-2.05compliance: STANDARDS-REF6standards:7 - id: ecss8 reference-only: true9gated: false10domain: space-systems11pack: space-systems12compatibility: "agentskills.io SKILL.md; any SKILL.md host (Claude Code, Hermes, OpenClaw)"13metadata:14 source: https://skillmd.com/skills/ashfordeou/q7045-tensile-testing15 domain: space-systems16 subdomain: ecss17 tags: [ecss, q-st-70-45-mechanical-testing-scope, q7045-tensile-testing, metallic-tensile-offset-proof-strength, tensile-ultimate-strength-peak, tensile-elongation-after-fracture, tensile-modulus-least-squares-window, tensile-reduction-of-area]18 version: 0.1.019 author: Aero Agent Skills20---2122# ECSS Mechanical Testing of Metals -- Tensile Testing (space-systems/ecss/q7045-tensile-testing)2324Use when the task is the tension test of the methods clause of25ECSS-Q-ST-70-45: a specimen of declared gauge length has been pulled to26fracture, the load-extension record has been converted to engineering stress27and strain, and the question is which properties the record supports and28which of them have to be reported with a caveat.2930## Domain quick reference3132- Modulus is a fit, not a ratio of two points. It is the least-squares slope33 over a declared elastic window, and it only means anything alongside the34 quality of that fit; a window that has crept past the knee still returns a35 slope, and the slope it returns is too low and looks plausible.36- Proof strength is a crossing, not a sample. The offset line of slope E,37 shifted by the offset strain, meets the record inside one segment; the38 crossing is interpolated in that segment rather than snapped to whichever39 recorded point happens to sit nearest it.40- Ultimate strength is the peak of the engineering curve. On a ductile alloy41 the peak sits well before the last point, because necking drops the42 engineering stress while the specimen is still extending.43- Elongation and reduction of area come from the broken halves. Crosshead44 strain at fracture includes the compliance of the frame and the grips, so45 it is a machine property, not a material property.46- A specified minimum is a floor the measured value may sit exactly on. A47 property landing on its minimum is compliant, and rejecting it is a defect48 of the comparison, not a finding about the material.4950## Workflow51521. Validate the record: every point carries a strain and a stress, neither is53 negative, and the strain strictly increases through the whole record.542. Fit the modulus over the declared elastic window, requiring at least three55 points inside it, and keep the fit quality beside the slope.563. Build the offset line from that modulus and the offset strain, walk the57 record for the segment where the record falls below it, and interpolate58 the crossing inside that segment.594. Scan for the peak engineering stress and keep the strain it occurred at,60 so uniform elongation is available and necking is visible.615. Reduce the broken halves into elongation after fracture and, when the62 fracture section was measured, reduction of area.636. Compare each property against its specified minimum with an inclusive64 test, and report the modulus fit quality as a finding when the declared65 window was not elastic.6667## Pitfalls6869- Taking the modulus from the first and last point of the window. Two points70 always fit a line perfectly and the fit quality that would have exposed the71 bad window is then unavailable.72- Reporting the last recorded stress as the ultimate strength. On anything73 ductile that is the fracture stress and it understates the material.74- Snapping the proof strength to the nearest sample. On a coarse record that75 moves the reported value by tens of megapascals with no trace in the report.76- Using crosshead travel for elongation after fracture. The frame and the77 grips are in that number and the specimen is not the only thing that78 stretched.79- Treating a property that lands exactly on its specified minimum as a80 failure. Floating-point representation of the minimum is what failed, and81 the comparison has to absorb it.8283## Behavior contract (gate 3)8485The record validation, least-squares modulus with its fit quality, offset86proof-strength crossing, peak detection, elongation and reduction of area,87and the comparison against specified minima are exercised by the gate 388contract test: scripts/test_q7045_tensile_testing.py against89scripts/q7045_tensile_testing_logic.py (stdlib unittest, offline). Run:90python3 scripts/test_q7045_tensile_testing.py9192## Compliance9394- ECSS standards are freely downloadable (ESA); cite the source and95 paraphrase per standards-map.yaml.96- compliance: STANDARDS-REF, gated: false.