ECSS Structures — Static Analysis Verification (space-systems/ecss/static-analysis-verification)
Use when the task is the static analysis verification of structural elements per ECSS-E-ST-32C clause 4.6.2.3 — confirming that computed stress, strain, and stability results carry non-negative margins of safety against the Design Yield Load (DYL) and Design Ultimate Load (DUL) at every structural level, using calculix-linear, calculix-nonlinear, or truss/beam hand methods.
Domain quick reference
- ECSS-E-ST-32C §4.6.2.3 defines two design load levels for structural verification: DYL (Design Yield Load, the load level at which permanent deformation is the limit) and DUL (Design Ultimate Load, the load level at which fracture or collapse is the limit). Both levels must show positive margins; yield limits typically govern metallic ductile failure modes and ultimate limits govern brittle or stability-driven failure modes.
- Margin of Safety (MOS) is the single acceptance criterion: MOS = (Allowable / |Applied|) − 1. A value of 0.0 is the minimum acceptable; any negative value is a structural finding requiring design action. Allowable values come from material data sheets, design allowables documents, or test-derived knock-down factors.
- Stability (buckling) uses a reserve factor: RF = Critical Load / Applied Load; MOS = RF − 1. The critical load may come from an eigenvalue (linear buckling, calculix-linear), a nonlinear collapse analysis (calculix-nonlinear), or a closed-form buckling formula (hand method for columns, plates, shells). A separate MOS is required for each buckling mode of concern.
- Structural levels addressed by this leaf: material coupon, detail element (bolt, lug, weld), component (bracket, fitting, panel), sub-assembly, and system. Each level carries its own applied load and allowable, derived from the model appropriate to that level.
- Analysis methods: calculix-linear (linear FEA, stress/strain extraction per element), calculix-nonlinear (geometric and/or material nonlinearity for post-buckling or plasticity), truss hand method (axial-only members, direct force/area), beam hand method (bending, shear, torsion formulae per cross-section).
Workflow
- Inventory all structural elements that are in scope for the current load case set. Assign each element to exactly one analysis tier: FEA (calculix-linear or calculix-nonlinear) or hand method (truss or beam). Elements that span tiers (e.g. a fitting verified by both FEA and a hand check) receive a separate MOS record per method; the governing (lowest) MOS controls.
- For each element, identify the applicable load-case pair: DYL for yield- critical failure modes (ductile metals under static load) and DUL for ultimate-critical failure modes (composites, castings, joints, any element with a scatter or knock-down factor applied). Both must be checked unless the design authority formally waives one with documented rationale.
- Extract the applied stress or strain from the analysis output (peak element stress in FEA, computed section stress in hand methods) and retrieve the corresponding allowable from the materials/allowables database. The allowable must be appropriate for the load type (yield allowable for DYL, ultimate allowable for DUL) and must account for temperature, surface finish, and any applicable knock-down.
- Compute MOS = (Allowable / |Applied|) − 1 for each element/load-type pair. Record the result with the element identifier, analysis method, and load type.
- For buckling-critical elements (columns, thin-walled panels, shells), also compute the stability MOS: extract the critical load from the eigenvalue or hand formula, divide by the applied compressive or shear load, subtract one. Apply the required knock-down factor to the critical load before computing the reserve factor when the analysis method is linear FEA (eigenvalue methods overestimate critical load for imperfection-sensitive structures).
- Flag every element/load-type pair where MOS < 0.0 as a structural finding. Flag every element that has a compressive load path but no stability check on record as an incomplete verification. Aggregate findings at each structural level; a level is not verified until all its element findings are resolved.
Pitfalls
- Applying a yield allowable at DUL or an ultimate allowable at DYL — the allowable must match the load level; mixing them produces a non-conservative margin for one level and an over-conservative margin for the other.
- Omitting the knock-down factor on a linear-buckling eigenvalue — eigenvalue critical loads do not account for geometric imperfections and can overstate the true critical load by 30–50 % for thin shells; a knock-down factor (empirically or analytically derived) must be applied before computing the stability MOS.
- Recording MOS = 0.0 as a marginal pass without noting it — a zero margin means there is no reserve at all; the analysis authority should document it as a known-tight margin requiring change-control scrutiny.
- Verifying only at the system level and skipping element-level margins — a positive system-level load path does not guarantee every detail element is within allowable; each fastener, lug, and weld must carry its own MOS record.
- Conflating applied strain with applied stress — strain-based allowables (composites, coupons) require strain extraction, not stress extraction, from the FEA output; using one in place of the other invalidates the MOS arithmetic.
Behavior contract (gate 3)
The load categorization, MOS computation, stress verification, stability verification, and aggregated analysis-run logic are exercised by the gate 3 contract test: scripts/test_static_analysis_verification.py against scripts/static_analysis_verification_logic.py (stdlib unittest, offline). Run: python3 scripts/test_static_analysis_verification.py
Compliance
- ECSS standards are freely downloadable (ESA); cite the source and paraphrase per standards-map.yaml.
- compliance: STANDARDS-REF, gated: false.
