ECSS Structures — Stress Intensity Factor K-Solutions (space-systems/ecss/stress-intensity-solutions)
Use when the task is selecting and evaluating the applicable K-solution for a crack geometry per ECSS-E-ST-32C clause 7.2.7 — categorizing the crack geometry, retrieving the matched solution from ESACRACK or an approved compendium, and computing the stress intensity factor with the correct boundary-correction factors before it feeds into crack-growth or fracture assessment.
Domain quick reference
- Clause 7.2.7 requires that the K-solution used in a fracture-control analysis be taken from ESACRACK or an equivalent peer-reviewed compendium, matched to the actual crack geometry and structural boundary conditions. The solution is not interchangeable between geometry families.
- Crack geometries are categorized into four principal families: surface semi-elliptical crack in a plate (uses Newman-Raju 1984 correction factors), center through crack in a plate (Feddersen finite-width correction), single edge through crack in a plate (Tada-Paris-Irwin polynomial), and quarter- elliptical corner crack at a circular hole (Kt-augmented solution). Each family has distinct governing parameters: a/c and a/t for surface cracks; a/W for through and edge cracks; a/R and a/t for corner-at-hole cracks.
- K is expressed in stress × length^0.5 units consistent with the fracture toughness K_Ic from the material allowables database. The Mode-I opening solution covers the vast majority of spacecraft structural cracks under tension-dominated loading; Modes II and III are secondary contributors and require separate mixed-mode assessment outside this leaf.
- The linear-elastic fracture-mechanics (LEFM) dominance condition must be checked: the plastic zone radius r_p = (1/(2π)) * (K/σ_ys)^2 must be small relative to the crack dimension a and the remaining ligament. When this condition is not met, an elastic-plastic correction (J-integral or CTOD approach) supersedes the K solution.
Workflow
- Categorize the crack geometry from the inspection record or initial-flaw assumption: identify the crack type (surface, through, edge, or corner), the relevant dimensions (a, c, t, W, R), and the primary loading mode (tension, bending, or combined). Reject any geometry whose parameters fall outside the validity bounds of the available K-solutions.
- Match the crack geometry to the appropriate K-solution family. Select the corresponding formula and correction-factor set from ESACRACK or the approved compendium entry. Record the solution reference (author, year, equation number) in the fracture-control analysis document.
- Evaluate the boundary-correction factors for the specific a/c, a/t, and
a/W ratios at each crack size step of interest:
- Surface semi-elliptical: compute the elliptic shape factor Q from the Newman-Raju approximation (Q = 1 + 1.464*(a/c)^1.65 for a/c ≤ 1), then evaluate the angular-correction terms M1, M2, M3 and the angular function f_phi at the parametric angle of interest (deepest point phi=90°, surface ends phi=0°).
- Center through crack (finite plate): apply the Feddersen secant correction K = sigma * sqrt(pia * sec(pia/(2*W))). Verify a < W.
- Edge through crack: apply the Tada-Paris-Irwin polynomial F(a/W) valid for a/W < 0.6; flag the solution if a/W exceeds this limit.
- Corner crack at hole: apply the Kt-augmented formula with effective stress concentration Kt_eff = 3*(1 - a/(a+R)), reduced by the empirical factor 0.97.
- Compute K = sigma * F * sqrt(pi*a/Q) (or the geometry-specific form) at each crack size. Confirm K is positive and increasing with crack size for tension loading; a non-monotonic result signals a parameter or formula error.
- Verify LEFM dominance: check that the plastic zone radius is small relative to the crack dimension and the remaining ligament. If the LEFM condition is violated, flag the result and escalate to an elastic-plastic method.
- Record the selected K-solution reference, the computed K vs. crack-size table, the validity bounds checked, and the LEFM dominance status in the fracture-control analysis note.
Pitfalls
- Applying a through-crack K-solution to a surface crack or vice versa — the through-crack formula treats the crack as spanning the full thickness (stress intensity is lower per unit depth than a surface crack where the crack front shape factor Q applies). Always match the solution to the actual crack front geometry from the inspection or initial-flaw assumption.
- Ignoring the a/W validity bound for the edge-crack polynomial — the Tada-Paris-Irwin formula is calibrated for a/W < 0.6 and diverges from the exact solution above that ratio. Use a full-range formula or a handbook table when a/W ≥ 0.6.
- Using K at phi=0° (surface intercept) as the governing point without checking phi=90° (deepest point) — for many surface-crack geometries the deepest point governs the crack-growth life, while the surface-end point governs when the crack is very shallow (a/t small) and wide (a/c small). Both points should be evaluated and the critical one selected.
- Omitting the LEFM check and applying K beyond the small-scale yielding limit — fracture toughness K_Ic values from test data already embed LEFM assumptions; applying them to a situation where the plastic zone is significant leads to unconservative life estimates.
Behavior contract (gate 3)
The geometry categorization, shape-factor evaluation, K computation, and LEFM dominance check logic is exercised by the gate 3 contract test: scripts/test_stress_intensity_solutions.py against scripts/stress_intensity_solutions_logic.py (stdlib unittest, offline). Run: python3 scripts/test_stress_intensity_solutions.py
Compliance
- ECSS standards are freely downloadable (ESA); cite the source and paraphrase per standards-map.yaml.
- compliance: STANDARDS-REF, gated: false.
