Opik Cipx

opik-cipx

opik-cipx is a local reverse HTTP proxy between Claude Code and the Anthropic API. Claude Code is pointed at it through ANTHROPIC_BASE_URL; opik-cipx owns the TLS leg to api.anthropic.com. It captures every call, attributes the token bill to cost buckets, and ships per-call spans to Opik. It is a single Go binary — both the long-lived gateway and the short-lived commands below.

How a session gets wired

Installing the plugin is the whole opt-in. Each Claude Code SessionStart runs the plugin's hook launcher, which locates the binary and execs opik-cipx sync (the hook event argument is ignored — sync is the same operation every time). From then on every API call flows through opik-cipx. There is no per-project or per-repo toggle and no marker file.

Wire path: Claude Code → http://127.0.0.1:9909 (plain HTTP, loopback) → opik-cipx tees the request and response → forwards over TLS to Anthropic. The proxy only tees bytes; categorization and span-building run on a background materializer so they never block the wire.

Turning capture on and off

• On: install the plugin, or run opik-cipx sync. It is on by virtue of being installed.
• Off: set CIPX_DISABLED to a truthy value (1, true, yes, on). The next opik-cipx sync tears the install down — removes the launchd / systemd supervisor unit and clears the managed ANTHROPIC_BASE_URL — so Claude Code routes straight to Anthropic. As a backstop, opik-cipx proxy exits 0 immediately while disabled. Disabling never breaks the Claude Code session.
• Back on: unset CIPX_DISABLED, then opik-cipx sync (or restart Claude Code). Settings take effect only on (re)start — there is no hot-reload.

CLI

All commands are subcommands of the single opik-cipx binary. Only opik-cipx proxy is long-lived; the rest are short-lived helpers.

• opik-cipx status [--json] — snapshot the running daemon (read-only).
• opik-cipx sync — the SessionStart entry point: install/refresh the OS supervisor, bring the daemon up if it's down, and point Claude Code's ANTHROPIC_BASE_URL at the proxy. Idempotent; safe to run anytime.
• opik-cipx restart — force the daemon to restart and pick up the latest binary on disk.
• opik-cipx logs — print and tail the gateway log.
• opik-cipx viewer [--open] — print (and with --open, launch) the debug-UI URL.
• opik-cipx purge — stop the daemon and wipe the WAL spool. Destructive: drops any spans not yet shipped to Opik.
• opik-cipx uninstall — stop the daemon, remove the supervisor unit, and delete ~/.opik-cipx. Destructive.
• opik-cipx proxy — run the gateway in the foreground (normally launched by the supervisor, not by hand).
• opik-cipx replay — re-derive spans from stored raw captures (offline, read-only).

sync and restart are the safe, idempotent repairs — non-destructive and fine to run on your own. purge and uninstall destroy state; confirm with the user before running either.

Where state lives

Everything is under ~/.opik-cipx/ (override the root with $CIPX_HOME), created at mode 0700:

• bin/ — the binary, when installed via the plugin or install.sh.
• logs/cipx.log — the gateway log (opik-cipx logs tails it).
• config.toml — optional config file (override its path with $CIPX_CONFIG).
• ports.json — assigned loopback ports, auto-bootstrapped on first start.
• state.json — daemon bring-up handshake (pid, started_at).
• spool/ — the write-ahead log that buffers spans; it survives Opik outages and drains when Opik is reachable again.
• sessions/<session_id>.json — per-session identity and repo metadata the SessionStart hook writes, joined onto spans at materialization.

Reading opik-cipx status

status reads state.json, then GETs /admin/stats on the admin loopback. Exit 0 = up, or not running (informational); exit 1 = state.json claims a pid but /admin/stats was unreachable (daemon wedged).

Header — running (pid N), the listener lines (claude_code, admin, and viewer, all on 127.0.0.1), uptime, project. not running → the daemon is down; run opik-cipx sync.

queue — in-memory, ready, inflight, wal hot (bytes buffered), last sync (age). wal hot climbing into hundreds of MiB, or last sync minutes stale → the shipper is stuck; read opik-cipx logs for errors against the Opik URL. A degraded true / last-error line means the WAL hit disk-write failures.

counters — healthy progress shows in requests_captured, events_materialized, spans_shipped. Flag any of these nonzero: materializer_errors_total, raw_captures_dropped, requests_dropped_queue_full, spans_dropped_term, unknown_endpoints (a route cipx doesn't recognize — often a Claude Code wire-format change ahead of an opik-cipx update), panics_recovered (a bug — surface ~/.opik-cipx/logs/cipx.log).

materializer — lag_events, inflight_raw, ready_raw; lag in the thousands that won't drain = materializer wedged → opik-cipx restart.

telemetry — off (no CIPX_SENTRY_DSN) is the default. It reads on only when CIPX_SENTRY_DSN is set and CIPX_SENTRY is not disabled.

--json exposes the raw /admin/stats. The hard signals when you need precision: stats.wal.degraded, stats.wal.last_write_error, and stats.wal.dropped_events_inmem / dropped_events_disk.

Configuration

Resolution precedence is env var → ~/.opik-cipx/config.toml → built-in default, and changes need a daemon (re)start. Env vars the binary actually reads:

• CIPX_DISABLED — master kill-switch (see above).
• CIPX_CAPTURE_CONTENT — false ships counts, costs, and structure but never prompt/completion bytes (redacted mode). Capturing content is the default.
• CIPX_HOME / CIPX_CONFIG — override the state root / config-file path.
• CIPX_UPSTREAM_PROXY — forward outbound traffic through another proxy.
• OPIK_CIPX_BASE_URL / OPIK_CIPX_API_KEY / OPIK_CIPX_WORKSPACE / OPIK_CIPX_PROJECT — the Opik destination, namespaced so they don't collide with the Opik SDK's own OPIK_* vars. OPIK_CIPX_DEBUG toggles debug.
• CIPX_SENTRY (off disables) and CIPX_SENTRY_DSN — anonymous error telemetry, opt-in via the DSN.

Invariants

• Loopback only. Proxy, admin, and viewer all bind 127.0.0.1 and refuse anything else at startup. If something suggests otherwise, that's a red flag, not a thing to "fix".
• Totals exact, categories proportional. Token totals come straight from Anthropic's response.usage; per-bucket numbers are chars-proportional estimates. No tokenizer is ever called.
• No bodies in logs or telemetry. Auth headers are redacted at capture and Sentry events are scrubbed. Quote error strings, never payloads.

Diagnosing

Run opik-cipx status first, then opik-cipx logs. sync and restart fix most daemon problems and are safe to run yourself; never purge or uninstall without asking. If the binary is missing entirely, the fix is reinstalling the plugin (/plugin install opik-cipx@opik-enterprise) or re-running install.sh — the daemon can't self-repair a missing binary.