Dry Gas Seal Screening
Use this skill for public, educational dry gas seal screening on centrifugal compressors. It estimates the seal-gas and separation-gas supply demand from the primary seal leakage rate and flags retrograde-condensation risk by comparing the seal cavity temperature against a hydrocarbon dew point at the seal/vent reference condition.
When to Use
- When a user asks whether a compressor dry gas seal has adequate seal-gas supply margin.
- When an agent needs a quick condensation-risk triage for the primary vent / standpipe dead-leg before a detailed seal study.
- When examples must run without confidential seal vendor data, machine line lists, or project seal-gas conditioning specifications.
Inputs
seal_leakage_rate_nl_per_min: primary seal leakage rate at standard conditions in NL/min per seal.
seal_cavity_temperature_c: seal cavity (process-side) temperature in degrees C.
hydrocarbon_dew_point_c: hydrocarbon dew point at the seal/vent reference condition in degrees C.
seal_count: number of seals supplied (default 2: drive end and non-drive end).
supply_margin: seal-gas supply margin over leakage, dimensionless, default 1.25.
separation_gas_rate_nl_per_min: separation (secondary) gas rate per seal in NL/min, default 0.0.
Outputs
total_seal_gas_supply_nl_per_min: screening seal-gas supply demand.
separation_gas_supply_nl_per_min: screening separation-gas supply demand.
seal_gas_supply_margin_ratio: the applied supply margin over leakage.
condensation_margin_c: seal cavity temperature minus the hydrocarbon dew point.
condensation_warning: ok, watch, or high (a small or negative margin means higher condensation risk).
assumptions: public assumptions used by the placeholder model.
Engineering Method
The Python class DryGasSealModel uses open, public concepts only:
- seal-gas supply demand is the primary seal leakage multiplied by the seal count and a supply margin, reflecting the API 692 intent that supply must exceed leakage to keep the seal faces clean.
- separation-gas supply demand scales with the seal count.
- the condensation margin compares the seal cavity temperature against a hydrocarbon dew point at the seal/vent reference condition. A small or negative margin flags retrograde condensation risk in the primary vent piping and standpipe dead-legs, which is the failure mode that seal-gas conditioning units exist to prevent.
This is educational and screening-only logic. It is not a seal vendor method, not a seal-gas conditioning design, and not a replacement for validated dry gas seal analysis and a qualified rotating-equipment review.
Python Usage Pattern
from dry_gas_seal_screening import DryGasSealModel
model = DryGasSealModel()
result = model.evaluate(
seal_leakage_rate_nl_per_min=280.0,
seal_cavity_temperature_c=44.0,
hydrocarbon_dew_point_c=40.0,
seal_count=2,
supply_margin=1.25,
separation_gas_rate_nl_per_min=120.0,
)
print(result.condensation_warning)
print(result.total_seal_gas_supply_nl_per_min)
print(result.condensation_margin_c)
If the optional neqsim Python package is available, the result records that fact so an agent can recommend moving to validated NeqSim seal-gas dew-point and condensation analysis. If it is not installed, the example still runs with public placeholder logic.
Validation Checklist
Common Mistakes
| Symptom |
Cause |
Fix |
| Condensation never flagged |
Dew point taken at cavity pressure instead of the vent/expanded condition |
Use the hydrocarbon dew point at the seal/vent reference condition |
| Supply demand looks low |
Supply margin set to 1.0 |
Use a supply margin above 1.0 consistent with the seal-gas control philosophy |
| Wrong total supply |
Seal count not matching the machine arrangement |
Set seal_count to the actual number of seals supplied |
Limitations
- No seal vendor leakage curves, clearance models, or qualification data are included.
- No isenthalpic (Joule-Thomson) expansion or transient standpipe cooldown is modelled.
- No seal-gas conditioning unit (heater/separator) sizing is performed.
- Not suitable for safety-critical, design, guarantee, or standards-compliance work.
Related NeqSim Functionality
neqsim.process.equipment.compressor.SealGasSupplyConditioning checks the supply side: dew point margin after the isenthalpic reduction across the seal gas supply valve, the heater temperature that restores the 20 K practice, the liquid load implied by a filter sump filling rate and the sump fill time. Use it before concluding that a seal problem is a filter problem.
- Evidence recipe from a field study (plant-agnostic): (1) find where the seal gas is taken (impeller, discharge, fuel gas) on the seal gas P&ID, because the contamination mechanism and the remedy differ; (2) compute the dew point margin at the supply conditions with the plant fluid; (3) detect filter drain events from the sump level sawtooth (level drop of more than 8 % in 15 min) and count them per day; (4) look for natural experiments (alternative supply gas, set-point step, shutdown) before regressing; (5) check that the filter analysis is not contaminated by priming diesel; (6) read the notification text of the seal and filter tags for design intent (orifice size, take-off location, O-ring quality).
neqsim.process.equipment.compressor.DryGasSealAnalyzer for vent-side condensation.
This educational screening corresponds to validated, rigorous functionality in the NeqSim Java library that a qualified engineer should use for design-grade work:
neqsim.process.equipment.compressor.DryGasSealAnalyzer — isenthalpic seal-gap expansion, retrograde condensation mapping, dead-leg cooldown, condensate accumulation, and seal-gas conditioning unit sizing per API 692.
neqsim.process.measurementdevice.HydrocarbonDewPointAnalyser — hydrocarbon dew-point evaluation for the seal-gas stream.
neqsim.process.equipment.valve.ThrottlingValve — Joule-Thomson expansion modelling across the seal gap.
In Python the same classes are reachable through the neqsim package (for example from neqsim import jneqsim).
References
1---2name: neqsim-dry-gas-seal-screening-23calculation_basis: "screening"4version: "0.1.0"5description: "Educational dry gas seal supply and condensation screening for centrifugal compressors. USE WHEN: a task needs a public, screening-level estimate of seal-gas and separation-gas supply demand and a seal-gas condensation-margin check (cavity temperature versus hydrocarbon dew point) before detailed dry gas seal system design per API 692."6last_verified: "2026-06-19"7requires:8 python_packages: []9 java_packages: []10 env: []11 network: []12metadata:13 source: https://skillmd.com/skills/equinor/neqsim-dry-gas-seal-screening-214---1516# Dry Gas Seal Screening1718Use this skill for public, educational dry gas seal screening on centrifugal compressors. It estimates the seal-gas and separation-gas supply demand from the primary seal leakage rate and flags retrograde-condensation risk by comparing the seal cavity temperature against a hydrocarbon dew point at the seal/vent reference condition.1920## When to Use2122- When a user asks whether a compressor dry gas seal has adequate seal-gas supply margin.23- When an agent needs a quick condensation-risk triage for the primary vent / standpipe dead-leg before a detailed seal study.24- When examples must run without confidential seal vendor data, machine line lists, or project seal-gas conditioning specifications.2526## Inputs2728- `seal_leakage_rate_nl_per_min`: primary seal leakage rate at standard conditions in NL/min per seal.29- `seal_cavity_temperature_c`: seal cavity (process-side) temperature in degrees C.30- `hydrocarbon_dew_point_c`: hydrocarbon dew point at the seal/vent reference condition in degrees C.31- `seal_count`: number of seals supplied (default 2: drive end and non-drive end).32- `supply_margin`: seal-gas supply margin over leakage, dimensionless, default 1.25.33- `separation_gas_rate_nl_per_min`: separation (secondary) gas rate per seal in NL/min, default 0.0.3435## Outputs3637- `total_seal_gas_supply_nl_per_min`: screening seal-gas supply demand.38- `separation_gas_supply_nl_per_min`: screening separation-gas supply demand.39- `seal_gas_supply_margin_ratio`: the applied supply margin over leakage.40- `condensation_margin_c`: seal cavity temperature minus the hydrocarbon dew point.41- `condensation_warning`: `ok`, `watch`, or `high` (a small or negative margin means higher condensation risk).42- `assumptions`: public assumptions used by the placeholder model.4344## Engineering Method4546The Python class `DryGasSealModel` uses open, public concepts only:4748- seal-gas supply demand is the primary seal leakage multiplied by the seal count and a supply margin, reflecting the API 692 intent that supply must exceed leakage to keep the seal faces clean.49- separation-gas supply demand scales with the seal count.50- the condensation margin compares the seal cavity temperature against a hydrocarbon dew point at the seal/vent reference condition. A small or negative margin flags retrograde condensation risk in the primary vent piping and standpipe dead-legs, which is the failure mode that seal-gas conditioning units exist to prevent.5152This is educational and screening-only logic. It is not a seal vendor method, not a seal-gas conditioning design, and not a replacement for validated dry gas seal analysis and a qualified rotating-equipment review.5354## Python Usage Pattern5556```python57from dry_gas_seal_screening import DryGasSealModel5859model = DryGasSealModel()60result = model.evaluate(61 seal_leakage_rate_nl_per_min=280.0,62 seal_cavity_temperature_c=44.0,63 hydrocarbon_dew_point_c=40.0,64 seal_count=2,65 supply_margin=1.25,66 separation_gas_rate_nl_per_min=120.0,67)6869print(result.condensation_warning)70print(result.total_seal_gas_supply_nl_per_min)71print(result.condensation_margin_c)72```7374If the optional `neqsim` Python package is available, the result records that fact so an agent can recommend moving to validated NeqSim seal-gas dew-point and condensation analysis. If it is not installed, the example still runs with public placeholder logic.7576## Validation Checklist7778- [ ] Inputs are in the documented units (NL/min, degrees C).79- [ ] Example inputs are public and synthetic.80- [ ] Tests cover ok, watch, high, and invalid-input cases.81- [ ] Results are described as educational screening indicators.82- [ ] Real seal system design is redirected to validated methods, API 692, and qualified review.8384## Common Mistakes8586| Symptom | Cause | Fix |87| --- | --- | --- |88| Condensation never flagged | Dew point taken at cavity pressure instead of the vent/expanded condition | Use the hydrocarbon dew point at the seal/vent reference condition |89| Supply demand looks low | Supply margin set to 1.0 | Use a supply margin above 1.0 consistent with the seal-gas control philosophy |90| Wrong total supply | Seal count not matching the machine arrangement | Set `seal_count` to the actual number of seals supplied |9192## Limitations9394- No seal vendor leakage curves, clearance models, or qualification data are included.95- No isenthalpic (Joule-Thomson) expansion or transient standpipe cooldown is modelled.96- No seal-gas conditioning unit (heater/separator) sizing is performed.97- Not suitable for safety-critical, design, guarantee, or standards-compliance work.9899## Related NeqSim Functionality100101- `neqsim.process.equipment.compressor.SealGasSupplyConditioning` checks the supply side: dew point margin after the isenthalpic reduction across the seal gas supply valve, the heater temperature that restores the 20 K practice, the liquid load implied by a filter sump filling rate and the sump fill time. Use it before concluding that a seal problem is a filter problem.102- Evidence recipe from a field study (plant-agnostic): (1) find where the seal gas is taken (impeller, discharge, fuel gas) on the seal gas P&ID, because the contamination mechanism and the remedy differ; (2) compute the dew point margin at the supply conditions with the plant fluid; (3) detect filter drain events from the sump level sawtooth (level drop of more than 8 % in 15 min) and count them per day; (4) look for natural experiments (alternative supply gas, set-point step, shutdown) before regressing; (5) check that the filter analysis is not contaminated by priming diesel; (6) read the notification text of the seal and filter tags for design intent (orifice size, take-off location, O-ring quality).103- `neqsim.process.equipment.compressor.DryGasSealAnalyzer` for vent-side condensation.104105This educational screening corresponds to validated, rigorous functionality in the NeqSim Java library that a qualified engineer should use for design-grade work:106107- `neqsim.process.equipment.compressor.DryGasSealAnalyzer` — isenthalpic seal-gap expansion, retrograde condensation mapping, dead-leg cooldown, condensate accumulation, and seal-gas conditioning unit sizing per API 692.108- `neqsim.process.measurementdevice.HydrocarbonDewPointAnalyser` — hydrocarbon dew-point evaluation for the seal-gas stream.109- `neqsim.process.equipment.valve.ThrottlingValve` — Joule-Thomson expansion modelling across the seal gap.110111In Python the same classes are reachable through the `neqsim` package (for example `from neqsim import jneqsim`).112113## References114115- NeqSim repository: https://github.com/equinor/neqsim116- NeqSim Skills Guide: https://github.com/equinor/neqsim/blob/master/docs/integration/skills_guide.md117- Public rotating-equipment references such as API 692 (Dry Gas Sealing Systems) and API 614 (Lubrication, Shaft-Sealing, and Oil-Control Systems) for general seal-gas concepts.