Server Hardening

server-hardening

When to use

Use when a host is yours to operate — a VPS, a bare-metal box, a long-lived VM — and its own security posture is the question. Three surfaces: who may log in, what may reach the network, and how patches arrive.

Do NOT use when:

• The workload runs on a managed runtime with no host you control — there is no host posture to set, and operational-readiness records that as unavailable with that reason
• Auditing application code for vulnerabilities (use security-audit)
• Application-level auth and authorization (use security, authz-review)
• Provisioning cloud infrastructure (use terraform, aws-infrastructure)
• Container image hardening (use docker)

The three surfaces

1. SSH posture

The one remote-entry door. Harden in this order, and keep an open session while you change it — a mistake here locks you out of the machine you are fixing.

Verify from a second connection before closing the first:

sudo sshd -t                                  # config parses; do this before reload
sudo systemctl reload ssh                     # or sshd, per distro
sudo sshd -T | grep -Ei 'passwordauth|permitrootlogin|pubkeyauth'

sshd -T prints the effective configuration. A file under sshd_config.d/ or a Match block can override what you just edited, so the file you wrote is not evidence — the effective dump is.

2. Firewall baseline

Default-deny inbound, allow-list outbound where the workload permits.

sudo ufw default deny incoming
sudo ufw default allow outgoing
sudo ufw allow OpenSSH                        # before enabling, or you are locked out
sudo ufw enable
sudo ufw status verbose                       # the verification, not the intent

Two traps worth naming. A container runtime can write its own forwarding rules that bypass the host firewall entirely — check the actual rule table (sudo iptables -S / sudo nft list ruleset), not just the friendly front-end. And a cloud security group sits in front of the host: both must agree, and the narrower one is the effective policy.

Optionally add an SSH brute-force throttle (fail2ban or equivalent). It is noise reduction and a small real gain once password auth is already off — never a substitute for it.

3. Unattended security upgrades

Patches that require a human are patches that arrive late.

sudo apt install unattended-upgrades          # Debian/Ubuntu family
sudo dpkg-reconfigure -plow unattended-upgrades
sudo unattended-upgrade --dry-run --debug     # proves it would act

Decide and record two things, because the default is silence: whether the host reboots automatically when a patch needs it, and where the failure notification goes. An upgrade timer that has been failing for six weeks is indistinguishable from one that is working, unless something reports it.

Security patches only. Automatic feature upgrades change behaviour under you, which is a different risk with a different owner.

Procedure: Harden a host

1. Confirm the host is yours to harden. Managed runtime with no shell → stop; there is no posture here, and that is a recordable unavailable.
2. Open a second session and keep it open for the whole SSH and firewall work. This is the entire rollback mechanism.
3. Set the SSH posture, then verify with sshd -T from the second session — effective config, not the file.
4. Set the firewall baseline, allowing SSH before enabling. Verify with ufw status verbose and against the raw rule table.
5. Enable unattended security upgrades, then prove with --dry-run that it would act. Record the reboot policy and the failure destination.
6. Re-verify from a fresh connection. Close every old session and reconnect. A posture that only holds inside an already-authenticated session is unverified.
7. Report each surface as met, unmet or uninspected. Uninspected is not met — operational-readiness reads an uninspected host posture as a red.

Validate

• Verify sshd -T reports passwordauthentication no.
• Verify sshd -T reports permitrootlogin no or prohibit-password.
• Verify a key-based login succeeds from a fresh connection.
• Verify the firewall default is deny-inbound and SSH is explicitly allowed.
• Verify the raw rule table agrees with the front-end.
• Verify unattended-upgrade --dry-run reports it would act.
• Confirm the reboot policy and the failure-notification destination are recorded.

Output format

1. One row per surface — SSH, firewall, unattended upgrades — with met / unmet / uninspected and the verifying command's output.
2. The reboot policy and where upgrade failures are reported.
3. Anything left unmet, with what would close it.

Gotcha

• Changing SSH without a second open session is how a host becomes unreachable.
• The config file is not the posture. sshd -T is; a drop-in or Match block silently wins.
• Enabling a firewall before allowing SSH locks you out immediately.
• A container runtime's own rules can bypass the host firewall.
• A cloud security group and the host firewall must both allow a port; the narrower wins.
• A silently failing upgrade timer looks exactly like a working one.
• A non-default SSH port reduces log volume, not risk.

Do NOT

• Do NOT disable password authentication before a key login is proven to work.
• Do NOT enable the firewall before allowing SSH.
• Do NOT enable automatic feature upgrades — security patches only.
• Do NOT treat an installed package as an enabled control; prove it acts.
• Do NOT report an uninspected surface as met.
• Do NOT rely on a non-default port as a control.

Auto-trigger keywords

• server hardening
• host hardening
• ssh hardening
• firewall baseline
• unattended upgrades
• fail2ban