Openwrt Mesh Lxc Wifi

OpenWrt Mesh LXC WiFi Management

Container Setup Requirements

1. Mesh satellite nodes (wifi_nodes:!router_nodes) run OpenWrt in a privileged LXC container instead of a VM. This allows WiFi management via WDS AP/STA without requiring PCIe passthrough (IOMMU/VT-d).

2. Key differences from VM pattern:

   • No routing — mesh containers are NOT routers. They run WDS STA only
   • Uses OpenWrt rootfs tarball (openwrt-*-rootfs.tar.gz), not VM disk image
   • Must be privileged (unprivileged: false) for PHY namespace move
   • Must set --ostype unmanaged because Proxmox cannot auto-detect OpenWrt
   • Container readiness uses ls / (not hostname, which is absent in BusyBox)
   • lxc_ct_skip_debian_cleanup: true to avoid dpkg operations on OpenWrt
   • Proxmox hookscript re-moves WiFi PHY after container restarts

WiFi PHY Namespace Management

3. The container receives host's WiFi PHY via iw phy <phy> set netns <pid> (network namespace move).

4. Load common WiFi kernel modules (iwlwifi, ath9k, etc.) on host BEFORE container creation and PHY move.

5. Detect PHYs in /sys/class/ieee80211/. If no PHYs found, hard-fail. All wifi_nodes are expected to have WiFi. Missing WiFi usually means stale vfio-pci bindings from previous run or missing firmware.

WiFi Detection Patterns

6. IMPORTANT: Detect WiFi radios inside LXC containers with iw phy (netlink), NOT ls /sys/class/ieee80211/ (sysfs). LXC containers bind-mount host's sysfs, which doesn't reflect network-namespace-specific entries like WiFi PHYs.

7. iw phy queries kernel via netlink and correctly sees PHYs moved into container's network namespace. The iw package must be pre-installed in custom image or via opkg install iw.

8. Previous bug: ls /sys/class/ieee80211/ inside container returned empty despite successful iw phy set netns — sysfs showed host's view.

Module Loading Constraints

9. NEVER modprobe WiFi modules inside container via pct_remote. modprobe inside container runs on HOST kernel (containers share kernel). If module reloads, new PHY appears in HOST namespace, not container namespace — effectively un-doing PHY namespace move.

10. Previous bug: modprobe iwlwifi inside container via pct_remote caused PHY to revert to host namespace. WiFi detection inside container then found zero radios despite successful namespace move.

VFIO Binding Cleanup

11. proxmox_pci_passthrough cleans stale vfio bindings on non-router hosts. If WiFi was previously bound to vfio-pci, the role removes blacklist-wifi.conf and vfio-pci.conf, unbinds devices, and reloads drivers.

12. Previous bug: mesh1 WiFi was bound to vfio-pci from prior test cycle. /sys/class/ieee80211/ was empty despite hardware being present.

UCI Wireless Configuration

13. After WiFi PHY is namespace-moved into container, OpenWrt does NOT auto-generate /etc/config/wireless. The configure role MUST run wifi config inside container to generate wireless configuration from detected hardware BEFORE any uci set wireless.radio* commands.

14. Previous bug: uci set wireless.radio0.disabled=0 failed on both mesh1 and mesh2. PHY was detected by iw phy (found phy0), but UCI wireless config had no matching radio0 section because PHY was moved into namespace after container booted.

WiFi Band Selection and Cross-Endpoint Negotiation

15. Bridge WiFi parameters (band, channel, htmode) are selected dynamically via cross-endpoint negotiation. The scripts/wifi_negotiate.py module receives capabilities from both AP and STA endpoints and computes the optimal shared config. NEVER hardcode band/channel for bridge containers.

16. The negotiation play in site.yml runs between provision and configure:

    • Collects capabilities from each bridge container via wifi_setup.sh capabilities
    • Runs wifi_negotiate.py on the controller to compute shared band/channel/htmode
    • Stores results as wifi_negotiated_* facts on bridge hosts
    • The configure role reads these facts; falls back to auto for standalone scenarios

17. Intel AX210 iwlwifi self-managed regulatory (LAR) blocks 5GHz AP mode (PASSIVE-SCAN on all 5GHz channels). The lar_disable module parameter does NOT exist in kernel 6.17+. However, 6GHz channels ARE AP-capable with self-managed regulatory. A sysfs rebind (tasks/sysfs_wifi_rebind.yml) in proxmox_pci_passthrough reinitializes the firmware regulatory state, enabling AP-capable 6GHz channels. NEVER use modprobe -r — use sysfs unbind + PCI rescan + explicit bind instead.

18. wifi_setup.sh now has a capabilities subcommand that outputs structured KEY=value data: supported bands, AP-capable channels, DFS channels, maximum widths, HE/VHT support, WDS support, and WPA3 support. This output is parsed by wifi_negotiate.py via parse_capabilities().

19. Band priority: 6GHz > 5GHz > 2.4GHz. The negotiation selects the highest common band with AP-capable channels on both endpoints. 2.4GHz width is capped at 40MHz. Non-DFS channels are preferred.

20. Performance tuning is applied automatically during wifi_setup.sh configure: WiFi power save disabled, coexistence scanning disabled (noscan=1), DTIM period set to 3 for WDS. These are critical for dedicated backhaul links.

21. Previous bug: AX210 5GHz AP mode failed with PASSIVE-SCAN channels (LAR). 5GHz remains blocked by self-managed regulatory. Negotiation correctly falls through to 6GHz (AP-capable) or 2.4GHz (always AP-capable). Module reload enables 6GHz AP channels on AX210.

22. Mesh containers (non-bridge) auto-detect correctly because their hardware (Centrino N 105, etc.) typically only supports 2.4GHz. The wifi_setup.sh dynamic probing handles this without negotiation.

L2 Bridge Loop Hazard (CRITICAL)

19. NEVER put both ends of a WiFi bridge on the same L2 broadcast domain. When bridge-1 (AP) and bridge-2 (STA) containers both have eth0 on vmbr0 (same physical switch), the WiFi link creates a second L2 path between them, forming a broadcast storm loop:

bridge-1 vmbr0 → CT eth0 → br-lan → WiFi AP
    ~~~~ WiFi link ~~~~
bridge-2 WiFi STA → br-lan → CT eth0 → vmbr0 → switch → back to bridge-1

Every broadcast frame (ARP, DHCP, mDNS) loops infinitely, saturating the entire household LAN and WiFi. STP on OpenWrt's br-lan does NOT prevent this because the loop spans multiple external bridges (two Proxmox vmbr0 instances + physical switch) that don't participate in the same STP domain.

20. The correct bridge container topology depends on wifi_role:
    • AP mode (bridge-1): eth0 on proxmox_wan_bridge (vmbr0) — extends the household network over WiFi
    • STA mode (bridge-2): eth0 on the backhaul bridge (vmbr1) — receives WiFi traffic and outputs to the physical cable toward mesh2

This ensures no L2 loop: the WiFi link is the ONLY path between vmbr0 (via bridge-1) and vmbr1 (via bridge-2).

21. Previous catastrophe (2026-04-09): Agent changed bridge WiFi from non-functional 5GHz (channel 1 invalid) to working 2.4GHz channel 11. Both containers were on vmbr0 (same switch). The WiFi link completed the L2 loop, causing a broadcast storm that took down the entire household WiFi network. All units had to be powered off for recovery. The non-functional 5GHz config had been accidentally preventing the loop.

Bridge Container Network Assignment

22. The openwrt_bridge_lxc provisioning role MUST assign the container bridge based on wifi_role:

    • wifi_role: ap → proxmox_wan_bridge (vmbr0)
    • wifi_role: sta → backhaul bridge (vmbr1, detected from non-management USB NIC)
    • If no backhaul bridge exists for STA mode → hard-fail (the architecture requires a physical cable)

23. NEVER use bridge link show dev <iface> master <bridge> exit code alone to detect bridge membership. The command returns exit code 0 with EMPTY output when the interface is NOT a member. ALWAYS check that the output is non-empty: output=$(bridge link show dev "$iface" master "$br" 2>/dev/null); if [ -n "$output" ]; then ....

    • Previous catastrophe (2026-04-09): The bridge detection loop checked only exit code. bridge link show dev enx00e04c68007a master vmbr0 returned 0 (empty output), so the loop matched vmbr0 (the FIRST bridge checked) instead of vmbr1 (the actual member). Bridge-2 STA container was provisioned on vmbr0. When WiFi associated, the L2 loop formed and the household network went down a second time.

Safety Gates (MANDATORY)

24. The provisioning role includes three safety gates that MUST NOT be removed:
    • Pre-provision gate: If wifi_role=sta and _backhaul_bridge == proxmox_wan_bridge, hard-fail immediately. STA on the WAN bridge = guaranteed broadcast storm.
    • Post-provision gate: After proxmox_lxc creates the container, read back the actual pct config bridge assignment. If STA container is on the WAN bridge, stop the container and hard-fail. This catches bugs in detection logic or the LXC provisioning helper.
    • Runtime storm guard: A systemd service (bridge-storm-guard.service) monitors the WAN bridge multicast packet rate. If >500 packets/sec sustained for 3 checks (6 seconds), it stops the bridge container and exits. This is the last line of defense against loops caused by any mechanism.