Arduino Project Builder

Arduino Project Builder Skill

Purpose: Assemble complete, working Arduino projects from requirements. This skill combines multiple patterns (sensors, actuators, state machines, logging, communication) into cohesive systems.

When to Use: When user requests a complete project like "build an environmental monitor", "create a robot controller", "make an IoT temperature logger", or any multi-component Arduino application.

Quick Start

List available project types:

uv run scripts/scaffold_project.py --list

Create a complete project:

uv run scripts/scaffold_project.py --type environmental --board esp32 --name "WeatherStation"
uv run scripts/scaffold_project.py --type robot --board uno --output ./my-robot

Interactive mode:

uv run scripts/scaffold_project.py --interactive

Resources

• scripts/scaffold_project.py - CLI tool for project scaffolding (config.h, main.ino, platformio.ini, README)
• assets/workflow.mmd - Mermaid diagram of project assembly workflow

Supported Project Types

1. Environmental Monitors - Multi-sensor data loggers (temperature, humidity, light, air quality)
2. Robot Controllers - Motor control, sensor fusion, obstacle avoidance, state machines
3. IoT Devices - WiFi/MQTT data transmission, cloud integration, remote monitoring
4. Home Automation - Relay control, scheduled tasks, sensor-triggered actions
5. Data Acquisition Systems - High-frequency sampling, SD card logging, real-time visualization

Project Assembly Workflow

1. Requirements Gathering

• User Intent: Understand the project goal (what should it do?)
• Hardware Inventory: What sensors, actuators, and communication modules?
• Board Selection: Arduino UNO, ESP32, or Raspberry Pi Pico?
• Constraints: Power source, memory limits, real-time requirements

2. Architecture Design

• Component Diagram: Which sensors/actuators connect to which pins?
• Data Flow: How does data move through the system?
• State Machine: Does the project have distinct modes/states?
• Timing Requirements: What tasks run at what intervals?

3. Code Assembly

• Pull patterns from references/ (environmental-monitor, robot-controller, iot-device)
• Customize for user's hardware (pin assignments, sensor types)
• Integrate state machine (if project has modes)
• Add data logging (Serial, SD card, or EEPROM)

4. Testing & Validation

• Compilation Check: Does it compile for the target board?
• Memory Usage: Within board limits? (UNO has only 2KB SRAM)
• Pin Conflicts: No duplicate pin assignments?
• Timing Analysis: All tasks fit within loop execution time?

5. Documentation

• Wiring Diagram: Pin connections in text/ASCII format
• Usage Instructions: How to upload, configure, and run
• Serial Commands: What commands trigger actions?
• Troubleshooting: Common issues and fixes

Board-Specific Considerations

Arduino UNO/Nano (ATmega328P):

• 2KB SRAM → Keep arrays small, use F() macro for strings
• 10-bit ADC → Range 0-1023
• No WiFi → Use Serial or add external module

ESP32:

• 327KB SRAM → Can use large buffers
• 12-bit ADC → Range 0-4095
• Built-in WiFi/Bluetooth → Ideal for IoT projects
• Dual-core → Can run tasks in parallel

Raspberry Pi Pico (RP2040):

• 262KB SRAM → Plenty of room
• 12-bit ADC → Range 0-4095
• No WiFi (unless Pico W) → Serial or add module
• Dual-core → Advanced task scheduling

Quality Standards

All generated projects must include:

1. config.h - Hardware abstraction (board detection, pin definitions)
2. Non-blocking code - No delay() calls, use EveryMs timers
3. Error handling - Check for sensor failures, out-of-range values
4. Serial diagnostics - Print status messages, sensor readings
5. Memory safety - Bounds checking on arrays, CRC for stored data
6. Wiring documentation - Clear pin assignment table
7. Compilation testing - Verify it compiles for target board

Integration Checklist

Before delivering a project, verify:

• All sensor readings validated (NaN checks, range checks)
• Button inputs debounced (50ms minimum)
• I2C devices scanned and detected
• CSV logging includes headers
• State machine has default/error states
• EEPROM writes include CRC validation
• WiFi reconnection logic (ESP32 projects)
• LED indicators for system status
• Serial baud rate matches board (9600 for UNO, 115200 for ESP32)
• F() macro used for all string literals

Common Project Patterns

1. Sensor → Filter → Display → Log

• Read sensor with EveryMs timer
• Apply MovingAverageFilter or MedianFilter
• Print to Serial every 5 seconds
• Log CSV every 60 seconds

2. Button → State Machine → Actuator

• DebouncedButton detects input
• State machine transitions modes
• Actuator (motor, relay, LED) responds to state

3. Sensor → Threshold → Action

• Continuous sensor monitoring
• If value exceeds threshold, trigger action
• Hysteresis to prevent oscillation

4. Multi-Sensor → Data Logger → SD Card

• Multiple EveryMs timers for different sensors
• Aggregate data into struct
• Buffered SD card writes (flush every 10 entries)

5. IoT: Sensor → WiFi → MQTT → Cloud

• ESP32 connects to WiFi
• Read sensors every 60 seconds
• Publish JSON to MQTT broker
• Reconnect logic if connection drops

Project References

See references/ directory for complete project examples:

• project-environmental-monitor.md - Multi-sensor data logger
• project-robot-controller.md - Button-controlled robot with obstacle avoidance
• project-iot-device.md - ESP32 temperature/humidity logger with WiFi
• project-home-automation.md - Relay controller with scheduled tasks
• project-data-acquisition.md - High-speed ADC sampling with SD logging

Communication & Output

Present projects as:

1. Full .ino file (ready to upload)
2. Wiring table (pin connections)
3. Upload instructions (board selection, baud rate)
4. Usage guide (Serial commands, expected output)

Example Output Format:

=== Environmental Monitor for Arduino UNO ===

WIRING:
DHT22 → Pin 2
Photoresistor → A0
Button → Pin 3 (INPUT_PULLUP)
LED → Pin 13

UPLOAD:
Board: Arduino UNO
Baud Rate: 9600

USAGE:
- Press button to start/stop logging
- Send 'd' to dump CSV data
- LED blinks every 2 seconds (heartbeat)

CODE:
[Full .ino file here]

Next Steps: When user requests a project, ask clarifying questions about:

1. Hardware components (what sensors/actuators?)
2. Target board (UNO, ESP32, Pico?)
3. Data output (Serial, SD card, WiFi?)
4. Special requirements (battery power, waterproof enclosure?)

Then assemble the project using patterns from references/, customize for their hardware, and deliver a complete, tested system.