Find Oep

find-oep

Smart trace-based OEP finder for packed/protected PE executables. Walks through unpacking stages using intelligent stepping, anti-debug evasion, and heuristic OEP detection. Once the OEP is found, captures a state snapshot for downstream use (PE reconstruction, analysis, etc.).

Instructions

1. Gather input and assess target

Ask the user (via AskUserQuestion) for any information not already provided:

• Target path — absolute path to the packed PE on disk
• x64dbg path — absolute path to x64dbg/x32dbg (if not already known)
• Bitness — 64-bit or 32-bit (default: 64)

Determine the CIP register name: rip for 64-bit, eip for 32-bit. Determine the stack pointer register: rsp for 64-bit, esp for 32-bit. Determine the debugger variant: x64dbg.exe for 64-bit, x32dbg.exe for 32-bit.

2. Launch the debugger and load the target

Use mcp__x64dbg__start_session with:

• executable_path: the packed PE path
• x64dbg_path: the appropriate debugger binary

Always start a new session for a clean environment. Wait for the debugger to settle — call mcp__x64dbg__get_debugger_status and confirm the debuggee is paused at the entry point. If running, call mcp__x64dbg__pause.

Record the session PID and x64dbg path for later reconnection.

3. Initial reconnaissance

Gather information about the packed binary to inform the unpacking strategy:

1. Capture entry state: Call mcp__x64dbg__get_all_registers to record the initial register state (especially the stack pointer — packers often restore it before jumping to OEP).
2. Memory map: Call mcp__x64dbg__get_memory_map to identify the module's sections, their protections, and any suspicious characteristics (e.g., sections with write+execute, sections with zero raw size but large virtual size, non-standard section names).
3. Entry point disassembly: Disassemble 50–100 instructions from the entry point using mcp__x64dbg__disassemble to identify the packer stub pattern.
4. YARA scan: Invoke /yara-sigs via Skill("yara-sigs") to identify the packer and obvious crypto/anti-debug signatures.
   • You may rerun this YARA scan if the packer contains self-decrypting code that hides signatures until unpacked.

Summarize findings to the user:

• Identified packer (if recognized)
• Section layout and anomalies
• Entry stub characteristics
• Recommended unpacking strategy

4. Heuristic OEP discovery (core loop)

This is the main unpacking loop. The goal is to trace through the packer stub and identify when execution transfers to the original, unpacked code.

OEP Heuristics

The OEP is likely reached when several of these conditions align:

Stepping strategy

1. Start at the packed entry point. Disassemble the current location.

2. Identify the current phase:

   • Decode loop: Repetitive instruction patterns (xor, mov byte, loop/dec+jnz). Set a breakpoint after the loop (on the first instruction following the loop exit) and go. If you cannot determine the loop exit, use mcp__x64dbg__trace_over with a break_condition that detects leaving the loop (e.g., a CIP range check).
   • API resolution: Calls to GetProcAddress, LoadLibrary*, hash-based API resolution. Step over these — they are building the IAT.
   • Anti-debug check: See step 6 for detection and evasion.
   • Inter-module call: Calls into system DLLs. Step over unless they appear suspicious.
   • Tail jump / OEP transfer: A jmp or push+ret that lands in a different section — potential OEP. Verify with the heuristics above.
   • Multi-stage transition: Decoded stub that itself decodes another layer. Repeat the process.

3. When in a repetitive region (same addresses appearing repeatedly):

   • Use mcp__x64dbg__trace_over with a break_condition like cip < <loop_start> || cip > <loop_end> to escape the loop efficiently.
   • Alternatively, identify the loop counter and set a conditional breakpoint: mcp__x64dbg__set_breakpoint with an appropriate condition.

4. At each significant transition, disassemble 20–30 instructions at the new location, check the memory section it belongs to, and evaluate the OEP heuristics.

5. Label and comment key addresses as you go: decode loop entries, API resolution routines, anti-debug checks, stage transitions, and the final OEP. Use mcp__x64dbg__set_comment and mcp__x64dbg__set_label.

5. Anti-debug detection and evasion

Packers frequently employ anti-debug techniques. When you encounter them, work around them to simulate non-debugged execution:

This list is not exhaustive. Always analyze the disassembly to understand the anti-debug technique being used and apply the appropriate evasion.

When you detect anti-debug behavior:

1. Inform the user what technique was found
2. Apply the evasion
3. Verify execution continues normally
4. Add a comment at the anti-debug location

Proactive anti-debug setup: At the start of unpacking, consider preemptively patching common PEB fields:

• Write 0x00 to PEB.BeingDebugged
• Write 0x00000000 to PEB.NtGlobalFlag This can be done via mcp__x64dbg__eval_expression to find peb(), then mcp__x64dbg__write_memory.

6. Confirm OEP

When you believe you've reached the OEP:

1. Disassemble 50+ instructions and verify the code looks like a real program entry (not packer stub code).
2. Check section: Confirm CIP is in the expected code section (.text or first section).
3. Check stack: Compare ESP/RSP to the initial value from step 3.
4. Check IAT: Read a few pointers from the import section — they should point to valid API functions in loaded DLLs. Use mcp__x64dbg__get_symbol to verify.
5. Inform the user with:
   • The OEP address
   • The section it's in
   • A disassembly listing of the first ~30 instructions
   • Confidence level and reasoning

Ask the user via AskUserQuestion: "OEP found at <address>. Take a state snapshot?"

If the user says no or wants to adjust, continue stepping as directed.

7. Capture state snapshot

Invoke /state-snapshot via Skill("state-snapshot") to dump the full debuggee memory state at the OEP. Note the snapshot output directory.

Report the final results to the user:

• OEP address and section
• Packer identified
• Anti-debug techniques encountered and evaded
• Snapshot output directory
• The debugger session remains open — the user can continue analysis or chain with other skills

8. Refresh GUI

Always call mcp__x64dbg__refresh_gui as the final step.