Verify the requested relationship between objects
Use general/SKILL.md for acquisition, transport and withdrawal. Identify the
required support, containment, engagement or alignment. Use
general/gripper/state-verification/SKILL.md for unresolved relationship evidence
and general/gripper/contact-effect/SKILL.md to diagnose an entry probe.
Preserve reference features and access
For a goal defined by an initial arrangement, record the destination references before moving those objects. Keep that reference separate from current contact coordinates. Distinguish position, orientation and support requirements; do not add a preferred orientation when the instruction leaves it unconstrained.
Choose visible features that distinguish the required orientation. An undirected long axis cannot distinguish opposite ends of an asymmetric part. Image slope alone is not world yaw; use calibrated geometry when numerical correction is needed. Inspect the object after reorientation because it can shift in the grip.
Preserve the receiver through acquisition and transport
Before acquiring the next object, confirm its receiver will remain stable, reachable and accessible through the transfer. Choose from observed behavior and the expected contact, rather than assuming every container needs two hands:
- Stable receiver and clear entry: place directly using its existing support.
- Sliding, rotation or tipping during contact, or expected contact that requires restraint: consider an available assisting hand or another stable support.
- Blocked opening or inaccessible interior: revise the approach, clear an
obstructing lid when permitted, or reposition the receiver before loading it.
If the working hand already holds a load, assess whether the free hand can
prepare the receiver while preserving that hold. Read
general/gripper/supported-contact/SKILL.mdfor adjustment or restraint. Holding an inaccessible receiver still does not make the route feasible.
Assign the assisting hand's role before pickup and preserve its existing support
responsibilities. Do not park it away or leave the receiver on moving support
without a viable plan. Use general/gripper/supported-contact/SKILL.md to establish
restraint without blocking entry; simultaneous motion of both hands is optional.
If the receiver moves, pause motion that depends on its old geometry. Recheck
its opening, floor, orientation and affected contents, then update the entry and
placement route. A held object's accurate world position does not establish its
position inside a displaced receiver. Restore a usable destination before
continuing. Use general/gripper/handover/SKILL.md for hand-to-hand support transfer and
general/gripper/held-object-geometry/SKILL.md for the load's actual clearance.
Build support and containment
- Keep a stable, reachable base when it already serves the next placement. For a spanning part, establish its supports before adding that load. After release, check that it actually rests on those supports rather than leaning against them or remaining supported by the hand.
- For nesting, align the actual receiving opening and the held part's rim or axis. Inspect tilt and edge contact; overlapping silhouettes do not establish that one part seated inside the other.
- For containment, check the whole object's position after withdrawal. A part can bridge a rim, protrude through an opening or be drawn back out by a finger. Leave room for subsequent entries and withdrawal before committing placement.
Establish engagement before advancing
Identify the entering feature and the receiving aperture, including their axes or planes. Keep the grasp clear of those features and the receiver stable. Choose alignment precision from their actual clearance. When observed alignment supports a bounded entry probe, test entry instead of repeatedly refining the same coordinates. If an edge catches or motion stalls, retract clear before correcting the mismatch; do not rotate while wedged or push deeper unchanged.
For turning after entry, preserve axis alignment, grip and receiver support. Use controlled segments and inspect relative part motion; grasp-site rotation alone does not establish advancement. If regrasping is needed, preserve the assembly's support first. A rotation about the grasp site can sweep an offset contact feature; use the held-object geometry and motion-recovery references when this matters.
Continue engagement until the required relation is established
After initial engagement, choose an observable relative progress measure and an end condition appropriate to the goal. Depending on the mechanism, useful evidence includes remaining gap, exposed length, relative angle, seating surfaces or a visible latch state. Initial entry is not full seating; resistance alone can mean an edge catch, obstruction or misalignment rather than the endpoint.
Choose contact checkpoints by a possible change in engagement, support, progress or proximity to the endpoint. A small commanded increment alone does not require remeasuring all geometry. At the checkpoint, inspect relative progress and the end condition using existing images first; obtain new evidence only where needed.
- Engagement maintained, progress observed, endpoint not reached: continue the effective operation in controlled segments while support and clearance hold.
- Engagement lost: restore alignment and control before further advancement.
- No progress: diagnose offset, tilt, slipping grip, obstruction or moving receiver; change the supported hypothesis instead of repeating more force.
- Endpoint supported by evidence: release when support permits, withdraw clear and verify the required relation without disturbing it.
Hand travel or resistance alone does not prove seating, tightening or locking. For example, while engagement holds and the gap visibly narrows, continue a bounded segment without resegmenting both parts. Shorten it near seating or a changed response; check an ambiguous endpoint. Reuse approaches only where the new parts' geometry is compatible. Do not infer unobserved torque or locking.
When withdrawal is required before reorientation, use separate move calls and
verify withdrawal before turning. A single pose target starts translation and
rotation together. Free-space transport may combine them when the observed
clearance and load permit it.