Homelab Network Setup
Use this skill to design a home or small-lab network that can grow without
needing a full rebuild.
When to Use
- Planning a new home network or redesigning an ISP-router-only setup.
- Choosing gateway, switch, and access point roles.
- Designing IP ranges, DHCP scopes, static reservations, and DNS.
- Preparing for future VLANs, Pi-hole, NAS, lab servers, or VPN access.
- Troubleshooting a new network that has double NAT, unstable Wi-Fi, or changing
server addresses.
How It Works
Start by separating device roles:
Internet
|
Modem or ONT
|
Gateway or router NAT, firewall, DHCP, DNS, inter-VLAN routing
|
Managed switch wired clients, AP uplinks, optional VLAN trunks
|
Access points Wi-Fi only; ideally wired backhaul
Servers and NAS stable addresses, DNS names, monitoring
Clients and IoT DHCP pools, isolated later if VLANs are available
Pick a gateway that matches the operator, not just the feature checklist:
| Option |
Best fit |
Notes |
| ISP router |
Basic internet only |
Limited control and often poor VLAN support |
| UniFi gateway |
Managed home network |
Good UI, ecosystem lock-in |
| OPNsense or pfSense |
Flexible homelab |
Strong VLAN, firewall, VPN, and DNS control |
| MikroTik |
Advanced network users |
Powerful, but easy to misconfigure |
| Linux router |
Tinkerers |
Document rollback before using as primary gateway |
IP Plan
Avoid the most common default, 192.168.1.0/24, when you expect to use VPNs.
It often conflicts with hotels, offices, and ISP routers.
Example small homelab plan:
192.168.10.0/24 trusted clients
192.168.20.0/24 IoT and media devices
192.168.30.0/24 servers and NAS
192.168.40.0/24 guest Wi-Fi
192.168.99.0/24 network management
Gateway convention: .1
Infrastructure reservations: .2 through .49
Dynamic DHCP pool: .50 through .240
Spare room: .241 through .254
Use home.arpa for local names. It is reserved for home networks and avoids the
leakage/conflict problems of ad hoc names like home.lan.
nas.home.arpa
pihole.home.arpa
gateway.home.arpa
switch-01.home.arpa
DHCP And DNS
- Use DHCP reservations for anything you SSH into, bookmark, monitor, or expose
as a service.
- Hand out the gateway as DNS until a local resolver is intentionally deployed.
- If using Pi-hole or another DNS filter, give it a reservation first, then point
DHCP DNS options at that address.
- Keep a small static/reserved range per subnet so replacements do not collide
with dynamic leases.
Cabling And Wi-Fi
- Prefer wired AP backhaul over mesh when you can run Ethernet.
- Use a PoE switch for APs and cameras if the budget allows it.
- Label both ends of each cable and keep a simple port map.
- Put the gateway, switch, DNS server, and NAS on UPS power if outages are common.
Examples
Beginner Upgrade
Goal: Keep the ISP router but stabilize a small lab.
- Set DHCP reservations for NAS, Pi, and any SSH hosts.
- Move local names to
home.arpa.
- Disable duplicate DHCP servers on secondary routers or APs.
- Wire the main AP instead of relying on wireless backhaul.
VLAN-Ready Plan
Goal: Prepare for future segmentation without enabling it immediately.
- Choose non-overlapping /24 ranges for trusted, IoT, servers, guest, and
management.
- Reserve .1 for the gateway and .2-.49 for infrastructure on every subnet.
- Buy a gateway and switch that support VLANs and inter-VLAN firewall rules.
- Document which SSIDs and switch ports will eventually map to each network.
Anti-Patterns
- Double NAT without a reason or documentation.
- Using
192.168.1.0/24 when VPN access is planned.
- Dynamic addresses for NAS, Pi-hole, Home Assistant, or other service hosts.
- Consumer routers repurposed as APs while their DHCP servers are still enabled.
- Flat networks with cameras, smart plugs, laptops, and servers all sharing the
same trust boundary.
See Also
- Skill:
network-interface-health
- Skill:
network-config-validation
1---
2name: homelab-network-setup
3description: Practical home and homelab network planning for gateways, switches, access points, IP ranges, DHCP reservations, DNS, cabling, and common beginner mistakes.
4metadata:
5 source: https://skillmd.com/skills/rajanthar/homelab-network-setup
6---
7
8# Homelab Network Setup
9
10Use this skill to design a home or small-lab network that can grow without
11needing a full rebuild.
12
13## When to Use
14
15- Planning a new home network or redesigning an ISP-router-only setup.
16- Choosing gateway, switch, and access point roles.
17- Designing IP ranges, DHCP scopes, static reservations, and DNS.
18- Preparing for future VLANs, Pi-hole, NAS, lab servers, or VPN access.
19- Troubleshooting a new network that has double NAT, unstable Wi-Fi, or changing
20 server addresses.
21
22## How It Works
23
24Start by separating device roles:
25
26```text
27Internet
28 |
29Modem or ONT
30 |
31Gateway or router NAT, firewall, DHCP, DNS, inter-VLAN routing
32 |
33Managed switch wired clients, AP uplinks, optional VLAN trunks
34 |
35Access points Wi-Fi only; ideally wired backhaul
36Servers and NAS stable addresses, DNS names, monitoring
37Clients and IoT DHCP pools, isolated later if VLANs are available
38```
39
40Pick a gateway that matches the operator, not just the feature checklist:
41
42| Option | Best fit | Notes |
43| --- | --- | --- |
44| ISP router | Basic internet only | Limited control and often poor VLAN support |
45| UniFi gateway | Managed home network | Good UI, ecosystem lock-in |
46| OPNsense or pfSense | Flexible homelab | Strong VLAN, firewall, VPN, and DNS control |
47| MikroTik | Advanced network users | Powerful, but easy to misconfigure |
48| Linux router | Tinkerers | Document rollback before using as primary gateway |
49
50## IP Plan
51
52Avoid the most common default, `192.168.1.0/24`, when you expect to use VPNs.
53It often conflicts with hotels, offices, and ISP routers.
54
55```text
56Example small homelab plan:
57
58192.168.10.0/24 trusted clients
59192.168.20.0/24 IoT and media devices
60192.168.30.0/24 servers and NAS
61192.168.40.0/24 guest Wi-Fi
62192.168.99.0/24 network management
63
64Gateway convention: .1
65Infrastructure reservations: .2 through .49
66Dynamic DHCP pool: .50 through .240
67Spare room: .241 through .254
68```
69
70Use `home.arpa` for local names. It is reserved for home networks and avoids the
71leakage/conflict problems of ad hoc names like `home.lan`.
72
73```text
74nas.home.arpa
75pihole.home.arpa
76gateway.home.arpa
77switch-01.home.arpa
78```
79
80## DHCP And DNS
81
82- Use DHCP reservations for anything you SSH into, bookmark, monitor, or expose
83 as a service.
84- Hand out the gateway as DNS until a local resolver is intentionally deployed.
85- If using Pi-hole or another DNS filter, give it a reservation first, then point
86 DHCP DNS options at that address.
87- Keep a small static/reserved range per subnet so replacements do not collide
88 with dynamic leases.
89
90## Cabling And Wi-Fi
91
92- Prefer wired AP backhaul over mesh when you can run Ethernet.
93- Use a PoE switch for APs and cameras if the budget allows it.
94- Label both ends of each cable and keep a simple port map.
95- Put the gateway, switch, DNS server, and NAS on UPS power if outages are common.
96
97## Examples
98
99### Beginner Upgrade
100
101Goal: Keep the ISP router but stabilize a small lab.
102
1031. Set DHCP reservations for NAS, Pi, and any SSH hosts.
1042. Move local names to `home.arpa`.
1053. Disable duplicate DHCP servers on secondary routers or APs.
1064. Wire the main AP instead of relying on wireless backhaul.
107
108### VLAN-Ready Plan
109
110Goal: Prepare for future segmentation without enabling it immediately.
111
1121. Choose non-overlapping /24 ranges for trusted, IoT, servers, guest, and
113 management.
1142. Reserve .1 for the gateway and .2-.49 for infrastructure on every subnet.
1153. Buy a gateway and switch that support VLANs and inter-VLAN firewall rules.
1164. Document which SSIDs and switch ports will eventually map to each network.
117
118## Anti-Patterns
119
120- Double NAT without a reason or documentation.
121- Using `192.168.1.0/24` when VPN access is planned.
122- Dynamic addresses for NAS, Pi-hole, Home Assistant, or other service hosts.
123- Consumer routers repurposed as APs while their DHCP servers are still enabled.
124- Flat networks with cameras, smart plugs, laptops, and servers all sharing the
125 same trust boundary.
126
127## See Also
128
129- Skill: `network-interface-health`
130- Skill: `network-config-validation`