Tailscale Subnet Router Debug

Tailscale Subnet Router Debug

Diagnose and fix Tailscale subnet router connectivity failures. Runs seven sequential checks covering the full route lifecycle from advertisement through return path verification.

What this skill does

1. Verifies the subnet router advertises the route.
2. Confirms the route is approved (admin console or autoApprovers).
3. Checks that clients accept subnet routes (--accept-routes).
4. Inspects policy routing table 52 for installed routes.
5. Validates IP forwarding is enabled on the subnet router.
6. Tests that the subnet router can reach the target directly.
7. Verifies the return path for response traffic.

Common triggers

• Client can ping the subnet router but not devices on the advertised subnet
• Route shows approved in admin console but ip route is empty
• Docker containers fail to advertise routes via TS_ROUTES
• Traffic flows to the target but responses never come back
• "It works from the router itself but not from other clients"

Diagnostic workflow

Run each step in order. Stop at the first failure and apply the fix before continuing — later steps depend on earlier ones.

Step 1 — Verify route is advertised

tailscale status --json | jq '.Self.AllowedIPs'

Pass: Subnet CIDR appears in AllowedIPs (e.g., 10.100.0.0/24).

Fail: Only Tailscale IPs shown. Route not advertised.

Fix: tailscale set --advertise-routes=<CIDR>. In Docker, check TS_ROUTES env var — it may not take effect if auth failed on first boot. Fall back to tailscale set at runtime.

Step 2 — Verify route is approved

Check admin console, or from a peer node:

tailscale status --json | jq '.Peer[] | select(.HostName=="<router>") | .AllowedIPs'

Pass: Subnet CIDR appears in the peer's view of the router's AllowedIPs.

Fail: Only Tailscale IPs shown from peer perspective. Route is pending approval.

Fix: Approve in admin console, or add autoApprovers to ACL:

"autoApprovers": {
  "routes": { "10.100.0.0/24": ["tag:subnet"] }
}

Step 3 — Verify client accepts routes

tailscale debug prefs | grep -i route

Fail: --accept-routes is false (the default). Clients ignore advertised subnet routes even when approved.

Fix: tailscale set --accept-routes=true. In Docker, add --accept-routes to TS_EXTRA_ARGS. Do not use tailscale down in Docker — it kills containerboot. Use tailscale set instead.

Step 4 — Verify route in policy routing table

ip route show table 52

Pass: Shows route for subnet CIDR via dev tailscale0.

Fail: Table 52 is empty or missing the subnet route.

Critical: ip route (no table) only shows the main table. Tailscale uses policy routing table 52 — routes will NOT appear in default output. This is the most common false negative.

Also check:

ip rule show

See references/policy-routing.md for details on table 52 and how Tailscale's policy routing works.

Step 5 — Verify IP forwarding on the subnet router

cat /proc/sys/net/ipv4/ip_forward

Pass: Returns 1.

Fail: Returns 0. Kernel drops forwarded packets silently.

Fix: sysctl -w net.ipv4.ip_forward=1. In Docker Compose, set sysctls: [net.ipv4.ip_forward=1]. For persistence on Linux hosts, add to /etc/sysctl.d/.

Step 6 — Verify network path from subnet router to target

From the subnet router:

ping <target-ip>
ip addr show

Pass: Router can reach the target and has an interface on the advertised subnet.

Fail: Router cannot reach the target. This is a local network issue (firewall, VLAN, routing) — not Tailscale.

Step 7 — Verify return path

The target must route responses back through the subnet router. If the target's default gateway is not the subnet router, return traffic takes a different path and gets dropped.

Fix: Add a static route on the target (or its gateway) for 100.64.0.0/10 pointing to the subnet router's internal IP. Or enable masquerading:

iptables -t nat -A POSTROUTING -o eth1 -j MASQUERADE

Tailscale 1.64+ enables --snat-subnet-routes by default, which handles this automatically.

Error handling

Do not silently skip a failed check. Report the specific failure with the fix before continuing. If a fix requires restarting Tailscale or recreating a container, instruct the user to do so and rerun from step 1.

References

• references/route-lifecycle.md — full 7-stage route lifecycle from advertisement through return path
• references/policy-routing.md — table 52, ip rule, VRF analogy, and why ip route misses Tailscale routes
• references/common-failures.md — symptom-based lookup table with root causes and fixes