thedixitjain Wi-Fi Reconnaissance
The first phase of any wireless engagement. Build a complete picture of the airspace before you deauth, evil-twin, or capture handshakes — every later attack depends on knowing the right BSSID, channel, encryption, and client population.
Quick Workflow
- Pick the right adapter for the target's band(s) and PHY
- Verify monitor mode + injection actually work
- Set the regulatory domain (legal channels and TX power)
- Sweep all bands passively
- Drill down on each in-scope BSSID for client population and PMF status
- Record everything in a structured target list before any active attack
Adapter Selection
| Chipset | Strengths | Notes |
|---|---|---|
| Atheros AR9271 (Alfa AWUS036NHA) | Solid 2.4 GHz monitor + injection | 802.11n only |
| Realtek RTL8812AU (AWUS036ACH) | Dual-band, injection | Driver: aircrack-ng/rtl8812au |
| MediaTek MT7612U (AWUS036ACM) | Stable dual-band | In-tree driver on modern kernels |
| MediaTek MT7921AU | Wi-Fi 6 monitor (limited) | Patched drivers required |
| AWUS036AXML / AXM | Wi-Fi 6E (6 GHz) | Bleeding edge — verify per release |
# Identify your radio
lsusb | grep -iE "(atheros|realtek|mediatek|alfa)"
iw dev
iw list | grep -A 8 "Supported interface modes"
iw list | grep -E "Frequencies:" -A 30
Monitor Mode Setup
# Kill conflicting services
sudo airmon-ng check kill
# Enable monitor mode
sudo airmon-ng start wlan0
# Or manually
sudo ip link set wlan0 down
sudo iw wlan0 set monitor control
sudo ip link set wlan0 up
# Verify monitor mode + injection
sudo aireplay-ng --test wlan0mon
The injection test should report 30/30 ack rates against nearby APs. Lower scores indicate driver, antenna, or position issues.
Regulatory Domain
# Check current
iw reg get
# Set explicitly (us = United States, jp = Japan extended, etc.)
sudo iw reg set US
Setting the right regdomain unlocks legitimate channels (US: 1–11 on 2.4, 36–165 on 5; JP adds 12–13 + 184+ DFS) and TX power. Operate within the regdomain you're authorized to use.
Passive Multi-Band Sweep
# All bands
sudo airodump-ng wlan0mon --band abg
# 5 GHz only (helps see UNII bands)
sudo airodump-ng wlan0mon --band a
# 6 GHz (requires 6E-capable adapter and updated airodump-ng)
sudo airodump-ng wlan0mon --band ax
# Hop only specific channels
sudo airodump-ng wlan0mon -c 1,6,11,36,40,44,48
Capture to file for later analysis:
sudo airodump-ng wlan0mon --band abg --write recon --output-format pcap,csv
Targeted Capture
Once you've identified an in-scope BSSID:
sudo airodump-ng -c 6 --bssid AA:BB:CC:DD:EE:FF -w target wlan0mon
Pin to the channel — channel-hopping during a focused capture loses frames.
Hidden SSIDs
Hidden APs broadcast beacons with empty ESSID. The name leaks during client probes (active scan) or association requests:
# Wait for legitimate client to associate, ESSID appears in airodump output
# Or, if a client is already associated, deauth them once to force reassociation:
sudo aireplay-ng --deauth 1 -a AA:BB:CC:DD:EE:FF -c 11:22:33:44:55:66 wlan0mon
(Only deauth with explicit authorization — see offensive-deauth-disassoc.)
Kismet for War-Driving
sudo kismet -c wlan0mon
# Open https://localhost:2501 for the dashboard
Kismet handles GPS integration, plots APs to a map, fingerprints by IE order, identifies probable IoT vendors from OUI prefixes, and tags known-vulnerable models.
For long-running captures, drop --no-ncurses and run headless under tmux.
Wigle Submission
If the engagement permits:
# Export Kismet's .kismet → CSV → Wigle import format
kismetdb_dump_devices --in capture.kismet --out devices.csv
(Wigle aggregates wireless network observations geographically — useful for mapping but check ROE.)
Vendor / OUI Identification
# Quick OUI lookup
echo "AA:BB:CC" | wireshark-tools/manuf-lookup
# Or check the airodump CSV's BSSID prefix against /usr/share/wireshark/manuf
Vendor identification informs:
- Likely default credentials (router brand → known defaults)
- Known firmware bugs (CVE per chipset)
- Whether WPS is likely vulnerable (Pixie Dust per chipset)
- Whether KRACK / FragAttacks patches are likely applied (vendor patch cadence)
Data to Record per Target
| Field | Why |
|---|---|
| BSSID | Required for every active attack |
| ESSID | Match against PNL probes; client probe correlation |
| Channel + width | Pin radio for capture |
| Band | Adapter selection |
| Encryption | WPA2-PSK / WPA2-Enterprise / WPA3-SAE / Open / WEP |
| PMF (Protected Management Frames) | Whether deauth works |
| RSSI | Position planning |
| Beacon interval / TIM | Anomaly detection vs. evil-twin defenders |
| Vendor (OUI) | Likely default creds, known bugs |
| Client list (MACs + RSSI) | Targets for deauth/relay |
| WPS enabled? | Pixie Dust candidate |
Detection Considerations
A defender's WIDS sees:
- New device entering the airspace (probe requests reveal even before association)
- Channel hopping patterns of monitor-mode interfaces
- Non-standard probe behavior (KARMA-style universal responses, see
offensive-evil-twin)
Pure passive recon (no probes from your radio) is invisible to most WIDS deployments. Stay passive until you're committed to the active phase.
Engagement Cheatsheet
# 1. Setup
sudo airmon-ng check kill && sudo airmon-ng start wlan0
sudo iw reg set US
sudo aireplay-ng --test wlan0mon # confirm injection (skip if pure passive)
# 2. Sweep all bands, write to file
sudo airodump-ng wlan0mon --band abg --write recon --output-format pcap,csv
# 3. Kismet for sustained map (optional)
sudo kismet -c wlan0mon --no-ncurses --daemonize
# 4. Per BSSID drill-down
sudo airodump-ng -c <ch> --bssid <BSSID> -w <name> wlan0mon
# 5. Build target list with all fields above
Key References
- IEEE 802.11-2020 (combined spec)
- aircrack-ng documentation: aircrack-ng.org
- Kismet documentation: kismetwireless.net
- WIGLE: wigle.net (read the API ToS before automated submissions)
- Source: https://github.com/SnailSploit/offensive-checklist/blob/main/wireless.md
Source: SnailSploit/Claude-Red → Skills/wireless/offensive-wifi-recon/SKILL.md