Tuyaopen/onchip Uart

TuyaOpen On-Chip UART (user serial)

⛔ STOP — for a "serial / 串口" request, confirm WHICH serial before ANY code

When the user says anything like "用串口发 X" / "send X over serial" / "发给电脑" / "用 USB 串口" without explicitly stating which kind, you MUST ask and WAIT before writing any code or choosing an API. Do NOT infer — "发给电脑" / "USB 串口" do not imply the log console.

Ask these two fixed options and wait for the user's choice — prefer an interactive multiple-choice prompt if your tooling supports one; otherwise list them as text:

你要用哪种串口?

1. 调试日志口（PR_*；T5AI 上就是 USB 转串口、电脑直接能收;零配置)
2. 独立用户串口（tal_uart；独立 UART 实例 + 自定义引脚)

• Picked 1 → just PR_NOTICE(...); no UART init, nothing recorded. Done.
• Picked 2 → continue with this skill (confirm instance + pins, record onchip:uart<N>).

❌ BAD: user says "用串口发 hello world 给电脑" → you write PR_DEBUG("hello world") without asking. ✅ GOOD: you ask the two options, wait for the answer, then write code only for the chosen path.

RED LINE — user UART vs log console (do not confuse)

• Which serial? → see the ⛔ STOP above: ask the two fixed options and wait; never assume the log console. PR_* = log console (not a peripheral, nothing recorded); tal_uart = dedicated user UART (this skill; confirm instance + pins, record onchip:uart<N>).

• Pick the UART from platform.json — do NOT guess roles. Read .tuyaopen/ide/platform.json → peripherals.uart.spec.ports[]. Each port carries:

  • role — its power-on default purpose: "log" (debug/log console), "download" (flash/download port), or "general" (free for app use). This is the default and is reconfigurable in code, but treat it as the guide.
  • pinGroups — its available TX/RX pin set(s).

  For a user UART, prefer a role:"general" port. Never use the log port (role:"log"). The download port is fine — its use is only transient during flashing, so it's free at runtime. Confirm the chosen instance with the user; don't infer roles from general board knowledge.

On-chip — no Kconfig, no TDD registration

• On-chip peripherals are provided by the platform. Do NOT write CONFIG_ENABLE_UART (or any CONFIG_ENABLE_SPI/I2C/GPIO) — those are platform-selected. No app_default.config change is needed.
• There is no board_register_hardware() / TDD step for a user UART. You call tal_uart_init() directly.

Step 1 — Confirm the instance and pins

A user UART is confirmed by which UART instance + which TX/RX pins.

Whether you need pin mux is decided by the port's pinGroups (from platform.json):

• Port with a single pinGroups entry → those are its fixed default pins. Do NOT call tkl_io_pinmux_config — just tal_uart_init() and use it. The vast majority of cases (and the SDK default TUYA_UART_NUM_0) are this. Don't mux "just in case".
• Port with multiple pinGroups → you must pick one; selecting a group needs mux. Only then #include "tkl_pinmux.h". E.g. T5AI UART2 exposes PIN31/30 or PIN41/40:

/* ALTERNATE-PINS ONLY — for a multi-group port; omit entirely for single-group ports */
#include "tkl_pinmux.h"
tkl_io_pinmux_config(TUYA_IO_PIN_40, TUYA_UART2_RX);
tkl_io_pinmux_config(TUYA_IO_PIN_41, TUYA_UART2_TX);

If the chosen port has one pin group, skip the block above and tkl_pinmux.h entirely.

Record the confirmed UART in .tuyaopen/used-peripherals.json as onchip:uart<N> before generating code — see the hardware-vibe-coding skill.

Step 2 — Init + send/receive

Default-pin case (the common one) — no pin mux, no tkl_pinmux.h:

#include "tal_api.h"

#define USR_UART_NUM   TUYA_UART_NUM_0   /* the UART the user confirmed; default pins → no mux */

void app_uart_init(void)
{
    TAL_UART_CFG_T cfg = {0};
    cfg.base_cfg.baudrate = 115200;
    cfg.base_cfg.databits = TUYA_UART_DATA_LEN_8BIT;
    cfg.base_cfg.stopbits = TUYA_UART_STOP_LEN_1BIT;
    cfg.base_cfg.parity   = TUYA_UART_PARITY_TYPE_NONE;
    cfg.rx_buffer_size    = 256;
    cfg.open_mode         = O_BLOCK;
    if (tal_uart_init(USR_UART_NUM, &cfg) != OPRT_OK) {
        PR_ERR("uart init failed");      /* PR_* = log console, fine to use */
        return;
    }

    const char *msg = "hello world\r\n";
    tal_uart_write(USR_UART_NUM, (const uint8_t *)msg, strlen(msg));
}

/* Polled receive + echo */
static void uart_rx_loop(void)
{
    uint8_t buf[256];
    for (;;) {
        int n = tal_uart_read(USR_UART_NUM, buf, sizeof(buf));
        if (n <= 0) { tal_system_sleep(10); continue; }
        tal_uart_write(USR_UART_NUM, buf, n);
    }
}

RX-by-interrupt instead of polling:

static void uart_rx_cb(TUYA_UART_NUM_E port, void *buff, uint16_t len) { /* ... */ }
tal_uart_rx_reg_irq_cb(USR_UART_NUM, uart_rx_cb);

API Reference

open_mode flags: O_BLOCK, O_ASYNC_WRITE, O_FLOW_CTRL, O_TX_DMA, O_RX_DMA.

Troubleshooting

Reference example

SDK: examples/peripherals/uart/ (UART init, write, polled read/echo, UART2 pin mux).