Tuyaopen/peripheral Ir

TuyaOpen TDL Infrared (IR)

IR supports transmit, receive, or full-duplex and two protocols: NEC (addr/cmd remote codes) and raw timecode (microsecond pulse arrays).

Usually a custom peripheral. Unless the board adapts IR, you register the driver yourself (pins + PWM-capable send pin + hardware timers), then use the TDL API. Add CONFIG_ENABLE_IR=y to app_default.config. The device name is chosen at registration time — there is no board NAME macro.

Driver Registration (TDD)

The send pin must support 38 kHz PWM output. One timer for single-timer mode.

#include "tdd_ir_driver.h"

static OPERATE_RET app_ir_register(char *name)
{
    IR_DRV_CFG_T hw = {
        .send_pin   = TUYA_GPIO_NUM_24,    // must support 38kHz PWM
        .recv_pin   = TUYA_GPIO_NUM_26,
        .send_timer = TUYA_TIMER_NUM_3,
        .recv_timer = TUYA_TIMER_NUM_3,    // used only in dual-timer mode
        .send_duty  = 50,                  // PWM duty %
    };
    return tdd_ir_driver_register(name, IR_DRV_SINGLE_TIMER, hw);
}

Headers

#include "tdd_ir_driver.h"
#include "tdl_ir_dev_manage.h"

Usage Template (NEC send + receive)

#include "tal_api.h"
#include "tkl_output.h"
#include "tdd_ir_driver.h"
#include "tdl_ir_dev_manage.h"

#define APP_IR_NAME "ir"

static IR_HANDLE_T s_ir_hdl = NULL;

void app_ir_init(void)
{
    app_ir_register(APP_IR_NAME);                 /* TDD register (see above) */

    if (OPRT_OK != tdl_ir_dev_find(APP_IR_NAME, &s_ir_hdl)) {
        PR_ERR("ir device not found");
        return;
    }

    IR_DEV_CFG_T cfg = {
        .ir_mode        = IR_MODE_SEND_RECV,      /* or _SEND_ONLY / _RECV_ONLY */
        .recv_queue_num = 3,
        .recv_buf_size  = 1024,
        .recv_timeout   = 300,                    /* ms */
        .prot_opt       = IR_PROT_NEC,            /* or IR_PROT_TIMECODE */
        .prot_cfg.nec_cfg = {
            .is_nec_msb = 0,                      /* 0 = LSB first */
            .lead_err = 31, .logics_err = 46,
            .logic0_err = 46, .logic1_err = 40, .repeat_err = 24,  /* % tolerances */
        },
    };
    if (OPRT_OK != tdl_ir_dev_open(s_ir_hdl, &cfg)) {
        PR_ERR("ir open failed");
    }
}

/* Send a NEC code at 38 kHz carrier. */
void app_ir_send_nec(uint16_t addr, uint16_t cmd)
{
    IR_DATA_U tx = {0};
    tx.nec_data.addr = addr;
    tx.nec_data.cmd  = cmd;
    tx.nec_data.repeat_cnt = 1;
    tdl_ir_dev_send(s_ir_hdl, 38000, tx, 1);      /* freq, data, send_cnt */
}

/* Block up to timeout_ms for a received frame. */
void app_ir_poll_recv(void)
{
    IR_DATA_U *rx = NULL;
    if (OPRT_OK == tdl_ir_dev_recv(s_ir_hdl, &rx, 3000) && rx) {
        PR_DEBUG("ir nec: addr=%04x cmd=%04x cnt=%d",
                 rx->nec_data.addr, rx->nec_data.cmd, rx->nec_data.repeat_cnt);
        tdl_ir_dev_recv_release(s_ir_hdl, rx);    /* MUST release */
    }
}

Raw timecode

uint32_t pulses[] = { 560, 560, 560, 1690, /* … µs high/low durations … */ };
IR_DATA_U tx = {0};
tx.timecode.data = pulses;
tx.timecode.len  = sizeof(pulses) / sizeof(pulses[0]);
tdl_ir_dev_send(s_ir_hdl, 38000, tx, 1);
/* On receive with IR_PROT_TIMECODE, read rx->timecode.len + rx->timecode.data[] */

API Reference

Modes & protocols

IR_MODE_RECV_ONLY  // 0      IR_PROT_TIMECODE // 0 — raw µs pulse array
IR_MODE_SEND_ONLY  // 1      IR_PROT_NEC      // 1 — addr/cmd codes
IR_MODE_SEND_RECV  // 2

NEC data: IR_DATA_U.nec_data = { uint16_t addr; uint16_t cmd; uint16_t repeat_cnt; }. Timecode data: IR_DATA_U.timecode = { uint16_t len; uint32_t *data; }.

Enable Macro

CONFIG_ENABLE_IR=y    # enables the IR subsystem (custom peripheral)

No Kconfig NAME macro — pass your chosen name to both tdd_ir_driver_register() and tdl_ir_dev_find().

Reference Example

examples/peripherals/ir/