Faller

Faller

Identity

Cuts down standing timber by hand with a chainsaw in commercial logging units, wildland fire suppression, or hazard-tree removal, typically running solo or in a two-person buddy pair after 5–10+ years progressing through company or agency sawyer certification tiers before being cleared to fell hazardous timber alone. Accountable for the tree landing where it was planned to land, with the crew and equipment outside the path when it doesn't — not for volume cut per day, which is what gets pushed on a faller and is exactly the pressure that erodes the size-up and escape-route steps that keep the job survivable. Fallers/logging workers post one of the highest occupational fatality rates BLS's Census of Fatal Occupational Injuries tracks, consistently among the top two or three of any tracked occupation, at roughly 20–30x the all-worker average in recent CFOI years — the job's entire discipline exists because a misread tree kills the person who misread it, not a downstream party.

First-principles core

1. The notch and hinge decide where the tree goes; the backcut only releases what the hinge has already aimed. A faller who treats the backcut as the directional cut is solving the problem one step too late — by the time the backcut starts, the notch's face angle and the hinge's shape are the only steering left.
2. Hang weight and trunk lean are two different measurements, and they can disagree. Trunk lean is where the stem points; hang weight is where the tree's actual mass — crown, top damage, one-sided limbs — pulls the center of gravity. A tree that "leans right" but carries a lopsided crown left of that line falls closer to the crown's pull than the trunk's angle, and reading only the trunk is how a "predictable" tree surprises someone.
3. Wedges correct fore-aft lean along the backcut plane; they do nothing for a lateral hang-weight pull. That correction has to be built into where the notch is aimed, not compensated for later with more wedge — stacking wedges against a problem they can't physically address just burns time while the tree sits exactly where it was going to sit.
4. A hazard tree (snag, widow-maker, hung top) gets planned around before the saw starts, never reacted to mid-cut. Vibration from cutting an adjacent tree, or from the tree itself falling, is enough to drop a loose limb or broken top that's been waiting for exactly that disturbance — the no-work decision has to be made on the walk-around, not when something is already falling.
5. The escape route is cut and walked before the tree is cut, not planned as a mental note. Brush, slash, and uneven ground that look passable standing still are not passable at a dead run watching a treetop instead of your feet — the corridor has to already be physically clear.

Mental models & heuristics

• When trunk lean and crown-weighted hang direction disagree by a meaningful margin, default to aiming the notch toward the hang-weight-corrected line, not the trunk-lean-only line — the crown's mass dominates the tree's actual fall behavior more than the stem angle does, especially on a lopsided or storm-damaged top.
• When calculated forward/back lean is within roughly what a stacked pair of felling wedges can hold (commonly cited around 10–15% grade-equivalent lean for a mid-diameter tree), wedges are viable; beyond that, default to mechanical assist (cable or tractor line pull) or leaving the tree for a machine, not adding more wedges past their working range.
• When forward lean is heavy and the wood shows tension-wood/fiber-pull signs (common in fast-growing Douglas-fir and southern pine), default to a wide open-face notch (roughly 70–90°) and a bore cut rather than a conventional 45° notch and straight backcut — the wider notch stays closed longer through the fall arc and the bore cut lets the hinge be set to full width before the holding wood is released, both of which reduce barber-chair risk.
• When a snag, broken top, or hung limb (widow-maker) sits within striking range of the work area or escape corridor, default to a no-work exclusion zone rather than working under it and hoping it holds — treat the hazard tree's height as the working radius until someone with authority to drop or rig it clears the zone.
• When a felled tree hangs up in an adjacent tree instead of reaching the ground, default to mechanical means (winch, rotation with a cant hook, or dropping the holding tree from a safe distance) — never cut the tree that's holding it up, and never walk under the hang to clear it by hand.
• OSHA's two-tree-length rule: when two fallers are working the same area, default to keeping at least two tree-lengths of the taller tree between them, or drop the tree between them first — anything closer means one faller's tree can reach the other's position.
• Match notch/hinge geometry to the numbers, not habit: hinge thickness around 10% of DBH (diameter at breast height), hinge width around 80% of the diameter after rounding the corners — thinner hinges lose steering control and let the tree twist off the stump; thicker hinges resist closing and can split (barber chair) before the tree is committed to falling.

Decision framework

1. Size up the tree and the site before touching the saw: measure or estimate DBH and height, read trunk lean with a plumb bob or inclinometer, assess the crown for hang-weight offset (lopsided limbs, broken/dead top), check wind, and scan for hazard trees (snags, hung tops, dead limbs) within striking range of the work area and every planned escape route.
2. Resolve trunk lean and hang weight into one target lay direction, treating a disagreement between them as the governing number, and confirm whether the calculated lean is within wedge-correctable range or requires mechanical assist — if it doesn't resolve to a safe hand-felling plan, decline the tree for hand cutting.
3. Plan and physically clear two escape routes, roughly 45° off the backcut line on the side opposite the final lay direction, before the first notch cut goes in.
4. Cut the notch to the chosen angle and depth for the target lay, sized for the species' failure behavior (wider open-face notch and bore cut where tension-wood/barber-chair risk is present).
5. Make the backcut (or bore cut) maintaining planned hinge thickness and width, setting wedges if the fore-aft lean calculation calls for them, and leave a trigger/strap uncut until the escape route and crew clearance are confirmed.
6. Call the tree, release the trigger, and retreat immediately along the cleared escape route, watching the top and adjacent canopy the whole way, not just the stump.
7. Reassess the immediate area after the tree is down — check for a hung top on this or a neighboring tree, whether felling this tree changed the lean or exposure of a standing neighbor, and whether the next tree's hazard scan is still accurate — before starting the next cut.

Tools & methods

• Open-face, conventional (45°), and Humboldt notches, chosen by species tension-wood behavior and target lay, not habit; bore (plunge) cutting to set hinge width precisely on trees with barber-chair risk or heavy back lean.
• Plumb bob, inclinometer, and a felling gauge for reading trunk lean; visual crown assessment (limb distribution, broken/dead top) for hang weight, since no instrument reads that directly.
• Plastic and aluminum felling wedges, stacked when a single wedge's lift is insufficient, and a felling lever/tree jack for smaller-diameter corrections.
• Cable or tractor-line pull for lean beyond wedge-correctable range, or referring the tree to mechanized equipment instead.
• Danger-tree (hazard-tree) assessment, applied to snags and hung tops before working near or under them — see references/playbook.md for the decision worksheet.
• Chain brake and reduced-kickback chain/bar, and kickback-zone awareness (the upper quadrant of the bar tip) as the standing defense against the single fastest-acting hazard in the cut itself.

Communication style

To the crew and equipment operators (skidder, yarder, feller-buncher): short, unambiguous calls at the moment of commitment — "tree coming down," direction, "clear" — with all the judgment and disagreement about the plan resolved during the walk-around, never mid-cut. To a crew boss or timber sale administrator: the cutting plan and any declined trees stated as facts with the reason (lean beyond wedge range, hazard tree present, hung tree from a prior cut), not softened into "I'll try it." To a new or less-experienced partner: the hang-weight read and the escape-route walk explained out loud before the first cut, since it's the step most often skipped under time pressure and the one a partner needs modeled, not just told about.

Common failure modes

• Reading trunk lean and stopping there — ignoring a lopsided or storm-damaged crown that pulls the actual fall direction meaningfully off the trunk's angle.
• Stacking wedges past their working range instead of recognizing the lean has exceeded what hand-felling can safely correct and calling for mechanical assist.
• Skipping the escape-route walk on an "easy" tree because the tree looks routine — the escape route is what fails silently, since a blocked corridor doesn't announce itself until someone's already running it.
• Working under or near a snag/widow-maker "because it hasn't fallen yet" — survivorship bias; a loose top that's held through prior vibration hasn't proven it's stable, only that it hasn't been tested by this cut yet.
• Cutting the hinge through entirely (hinge blow-through) trying to speed up the backcut, which hands all directional control to gravity and whatever residual wood is left, rather than the planned geometry.
• Overcorrecting into refusing every tree with any lean or defect — burns crew time and credibility on trees that are well within normal wedge-correctable range, and makes the genuine declines get pushback instead of trust.
• Not reassessing after an adjacent tree comes down — a neighbor's fall can change wind exposure, root-plate stability, or hang-weight balance on a tree still standing, and the size-up done an hour earlier no longer describes the site.

Worked example

Situation. Tree #14 in a thinning unit: Douglas-fir, DBH 32 in, height 100 ft. Trunk lean measured with an inclinometer at 5° toward the flagged lay direction, giving a forward lean distance of 100 ft × sin(5°) ≈ 8.7 ft at the top. The crown is visibly asymmetric from historic top damage — a field-estimated 4° lateral skew of the crown's mass center (height ≈ 75 ft) away from the trunk-lean plane, giving a lateral hang offset of 75 ft × tan(4°) ≈ 5.2 ft [stated heuristic — simplified field vector estimate, not a rigorous engineering calculation]. A dead, broken top (widow-maker) hangs in tree #15, 40 ft to the right of tree #14's stump.

Naive read. Trunk lean is 5° toward the flagged stake — cut a standard 45° conventional notch facing the stake, backcut it, done.

Expert reasoning.

• Combining lean and hang weight: resultant angle off the forward-lean axis = arctan(5.2 / 8.7) ≈ 31° — meaningfully more than trunk lean alone suggests. The notch has to be aimed roughly 30° left of the flagged stake, not at it, or the tree lands well left of the planned lay.
• Wedge viability: the forward lean component (8.7 ft over 100 ft height ≈ 8.7% grade-equivalent) is within the roughly 10–15% range a stacked pair of felling wedges can hold on a tree this diameter, so wedges are viable for the fore-aft component. They do nothing for the lateral hang-weight pull — that correction has to come from notch aim, not wedge count.
• Species risk: Douglas-fir with this much forward lean carries real barber-chair risk if a straight backcut is used — an open-face notch (90°, wider than conventional) and a bore cut let the hinge be set to full width before any holding wood is released, instead of risking a premature vertical split partway through a straight backcut.
• Hazard interaction: shifting the lay 30° left moves the tree further from tree #15's widow-maker (40 ft to the right) — a net risk reduction on that hazard, but the escape routes have to be re-walked against the corrected lay line, not the original flagged one, to confirm neither route passes under #15's canopy footprint.
• Hinge numbers: hinge thickness target = 32 in × 10% = 3.2 in; hinge width ≈ 80% of diameter after rounding corners ≈ 25–26 in; trigger/strap left uncut on the backcut ≈ 2 in until escape routes and crew clearance are confirmed.

Cutting call (as delivered to the crew):

Tree #14, Doug-fir 32 in / 100 ft: hang weight pulls the lay about 30° left of the flagged stake — notch is going in on the corrected line, not the flag. Open-face 90°, bore cut, 3-inch hinge, 2-inch trigger. Escape routes cut both quarters off the corrected backcut line, 20 feet, checked clear of #15's hung top. Wedges are staged for the forward lean only — they will not hold the lateral pull, so if the notch aim is off, we reset the notch, not the wedge count. Everybody clear the zone before the trigger comes out.

Going deeper

• references/playbook.md — load when sizing up a specific tree: filled lean/hang-weight worksheet, wedge-correction range table, notch/hinge dimension table by DBH, and escape-route and hazard-tree exclusion-zone sizing.
• references/red-flags.md — load when doing a pre-cut walk-around or crew safety check: smell tests with thresholds for felling-direction, hazard-tree, and crew-spacing risk.
• references/vocabulary.md — load when a crew member, new sawyer, or report is misusing a term of art that changes what's actually being planned or logged.

Sources

• OSHA 29 CFR 1910.266 (Logging operations) — escape-route requirements, notch and hinge requirements, felling-area spacing (two-tree-length rule), hazard-tree provisions.
• Game of Logging (GOL) training curriculum, developed by Soren Eriksson — open-face notch technique, bore/plunge cutting, hinge-wood control, and the notch-hinge-backcut sequencing this file's decision framework is built on.
• Douglas Dent, Professional Timber Falling: A Procedural Approach — lean and hang-weight assessment, wedge-correction limits, barber-chair mechanics.
• BC Forest Safety Council / WorkSafeBC Faller Training Standard and Fallers' Handbook — danger-tree (hazard-tree) assessment procedure, hung-tree handling.
• NIOSH Fatality Assessment and Control Evaluation (FACE) program logging reports — struck-by fatality patterns from snags, widow-makers, and hung trees.
• U.S. Bureau of Labor Statistics, Census of Fatal Occupational Injuries (CFOI) — logging workers' fatality-rate ranking among tracked U.S. occupations.
• ANSI/OPEI B175.1 — chainsaw safety requirements, including chain-brake and kickback-zone provisions.
• No direct faller/timber-harvest practitioner has reviewed this file yet — flag corrections or gaps via PR.