Schematic Gen

Schematic Generation

Two-layer system: this skill provides topology knowledge, vcli schematic commands provide the execution layer.

CLI Commands

# Atomic operations
vcli schematic open  --lib L --cell C [--view schematic]
vcli schematic place --master lib/cell --name I --x X --y Y [--params w=14u,l=1u]
vcli schematic wire  --net N x1,y1 x2,y2 ...
vcli schematic conn  --net N --from I:T --to I:T
vcli schematic label --net N --x X --y Y
vcli schematic pin   --net N --type input --x X --y Y
vcli schematic check
vcli schematic save

# Batch from JSON spec
vcli schematic build --spec file.json

JSON Spec Format

{
  "target": { "lib": "myLib", "cell": "ota5t", "view": "schematic" },
  "instances": [
    { "name": "M5", "master": "smic13mmrf/p12", "x": 0, "y": 4,
      "params": { "w": "14u", "l": "1u" } }
  ],
  "connections": [
    { "net": "vtail", "from": "M5:D", "to": "M1:S" }
  ],
  "globals": [
    { "net": "vdd", "insts": ["M5:S", "M5:B", "M1:B"] }
  ],
  "pins": [
    { "net": "vip", "type": "input", "connect": "M2:G", "x": -4, "y": 2 }
  ]
}

Workflow

1. Collect sizing — from gm/Id design or optimization results
2. Generate JSON spec — use topology template below, fill in W/L values
3. Run build — vcli schematic build --spec spec.json
4. Verify — vcli schematic check

Topology Templates

5T OTA (PMOS Diff Pair + NMOS Mirror Load)

     VDD
      |
     M5 (PMOS tail, gate=nbias)
      |
    vtail
    /    \
  M1      M2  (PMOS diff pair)
  |        |
  nd1    vout
  |        |
  M3      M4  (NMOS mirror load, M3 diode)
  |        |
    GND   GND

Terminal mapping (SMIC 130nm MOSFET):

• PMOS p12: terminals D G S B (drain gate source bulk)
• NMOS n12: terminals D G S B

{
  "target": { "lib": "myLib", "cell": "ota5t" },
  "instances": [
    { "name": "M5", "master": "smic13mmrf/p12", "x": 0,  "y": 8, "params": {} },
    { "name": "M1", "master": "smic13mmrf/p12", "x": -3, "y": 5, "params": {} },
    { "name": "M2", "master": "smic13mmrf/p12", "x": 3,  "y": 5, "params": {} },
    { "name": "M3", "master": "smic13mmrf/n12", "x": -3, "y": 2, "params": {} },
    { "name": "M4", "master": "smic13mmrf/n12", "x": 3,  "y": 2, "params": {} }
  ],
  "connections": [
    { "net": "vtail", "from": "M5:D", "to": "M1:S" },
    { "net": "vtail", "from": "M5:D", "to": "M2:S" },
    { "net": "nd1",   "from": "M1:D", "to": "M3:D" },
    { "net": "nd1",   "from": "M3:D", "to": "M3:G" },
    { "net": "nd1",   "from": "M3:G", "to": "M4:G" },
    { "net": "vout",  "from": "M2:D", "to": "M4:D" }
  ],
  "globals": [
    { "net": "vdd!", "insts": ["M5:S", "M5:B", "M1:B", "M2:B"] },
    { "net": "gnd!", "insts": ["M3:S", "M3:B", "M4:S", "M4:B"] }
  ],
  "pins": [
    { "net": "vip",   "type": "input",  "x": 6,  "y": 5 },
    { "net": "vin",   "type": "input",  "x": -6, "y": 5 },
    { "net": "nbias", "type": "input",  "x": -2, "y": 8 },
    { "net": "vout",  "type": "output", "x": 6,  "y": 2 }
  ]
}

Folded-Cascode OTA (PMOS Input)

     VDD
    / | \
  M5  M9  M10  (PMOS current sources)
  |   |    |
vtail M7   M8   (PMOS cascode)
 / \  |    |
M1  M2 |   vout
|    | |    |
M3  M4 M11  M12  (NMOS cascode)
|    |  |    |
M13 M14 M15  M16  (NMOS current source)
     GND

Additional instances: bias mirrors, cascode devices. Fill params from sizing.

Two-Stage Miller OTA

Stage 1:          Stage 2:
M5 (tail)         M7 (output NMOS)
 / \                |
M1  M2            vout---Cc---nd1
|    |              |
M3  M4            M6 (output load)

Compensation: Cc between nd1 and vout, optional Rz in series.

Coordinate Conventions

• Schematic coordinates in microns
• Y increases upward (VDD at top, GND at bottom)
• Symmetric pairs: mirror around x=0
• Typical spacing: 3 units horizontal, 3 units vertical between rows
• Pins placed at the edges (x = +-6 or more)

PDK Master Names

Params are PDK-specific. Always pass W/L via --params or JSON params field.

Label Placement — Auto-Rotation

When placing labels on terminals, pick rotation based on the stub direction rather than using a fixed angle. The stub direction is determined by the terminal geometry:

For schematic_label_instance_term_offset (label on a perpendicular branch off the stub), align the rotation with the branch direction, not the stub:

• branch "up" or "down" → R90
• branch "left" or "right" → R0

This avoids overlapping labels on crowded ports (e.g., MOS gate rows) and matches what Virtuoso's "Clean" cosmetic preset produces. When stub geometry is degenerate (rbDx or rbDy is nil, e.g. MOS-stub path), fall back to the user-supplied rotation.

Notes

• vcli schematic open must be called before other commands (opens cellview in GUI)
• conn uses schCreateWire for auto-routing between terminals
• wire uses exact coordinates — use when you need specific routing paths
• Global nets (vdd!, gnd!) use ! suffix in Virtuoso convention
• After build, always run check and save
• Always call dbClose after dbSave in SKILL loops that open cellviews programmatically; omitting it leaves views accumulating in Virtuoso memory across repeated invocations