Spectre Netlist Gotchas

Spectre Netlist-Mode Gotchas

Lessons from standalone Spectre simulation (no ADE/Virtuoso), covering vsource syntax, noise analysis setup, PSF ASCII parsing, and PM calculation for inverting topologies.

1. vsource AC Stimulus: mag= not ac=; type=dc suppresses AC

Problem

Two failure modes, both produce zero AC response with no error:

A) Using ac=1 causes SFE-30 (invalid parameter in native Spectre lang).

B) Any vsource without mag= has zero AC response by default — this is true whether or not type=dc is specified. The AC small-signal amplitude defaults to 0. Verified: vsource dc=1.0 and vsource dc=1.0 type=dc both produce (0.0 0.0) at every frequency. type=dc is not the cause; the absence of mag= is.

Root Cause

• ac= is SPICE-compatibility syntax only; native Spectre uses mag= for AC amplitude
• Default AC magnitude for all vsource types is mag=0 — must be set explicitly
• Typical trap: engineer sets up a DC supply for DC analysis, forgets mag=1 for AC

Fix

// ✗ WRONG — SPICE-compat only, causes SFE-30
Vip (vip 0) vsource dc=0.9 ac=1

// ✗ WRONG — no mag= → zero AC response (true with OR without type=dc)
VVDDA (VDDA 0) vsource dc=3.3
VVDDA (VDDA 0) vsource dc=3.3 type=dc   // same result — still zero AC

// ✓ CORRECT — pure AC stimulus
Vip (vip 0) vsource dc=0.9 mag=1

// ✓ CORRECT — DC supply with AC perturbation (PSRR measurement)
VVDDA (VDDA 0) vsource dc=3.3 type=dc mag=1 srcType=dc

Discovery

Run spectre -h vsource to see all valid parameters. The relevant parameter is: mag=0 V (Small signal voltage).

Symptom: AC analysis runs without error, all node voltages show (0.0 0.0) complex values → verify mag=1 is present on the excitation source.

2. Noise oprobe: Parallel Probe, Not Series

Problem

Noise analysis with a series resistor as oprobe gives wildly wrong results (e.g., millions of nV/√Hz instead of hundreds). The simulation completes with 0 errors — no warning that the result is nonsensical.

Root Cause

When oprobe is a series resistor (e.g., 1Ω between vout and CL), Spectre measures the voltage across that resistor, not the voltage at the output node.

At low frequencies, the CL capacitor is nearly open → almost no current flows through the series resistor → voltage across it ≈ 0. The "gain" from input to oprobe becomes tiny (e.g., 7.5e-9 V/V at 10 Hz instead of 118 V/V), and the input-referred noise is inflated by 1/gain.

Fix: Use a Large Parallel Resistor

// ✗ WRONG — series probe, measures V across resistor (≈ 0 at low freq)
Rout_probe (vout vout_s) resistor r=1
CL_out (vout_s 0) capacitor c=CL
noise_an noise start=10 stop=100e3 dec=20 oprobe=Rout_probe iprobe=Vip

// ✓ CORRECT — parallel probe, negligible loading, measures full vout
CL_out (vout 0) capacitor c=CL
Rout_probe (vout 0) resistor r=1e12
noise_an noise start=10 stop=100e3 dec=20 oprobe=Rout_probe iprobe=Vip

The 1TΩ parallel resistor:

• Sees the full output voltage (vout) across it
• Negligibly loads the circuit (1TΩ ≫ Rout of OTA)
• Spectre correctly reports the output noise voltage spectral density

Verification

Check the "gain" field in noise PSF output at low frequency. It should match your AC gain (e.g., ~118 V/V for a 41.5 dB amplifier). If gain ≪ 1, the oprobe is wrong.

3. oprobe Must Be a Circuit Element (SFE-1997)

Problem

Using a node name (e.g., oprobe=vout) causes error SFE-1997.

Fix

oprobe requires a circuit element (resistor, port, etc.), not a node name. Use the 1TΩ parallel resistor pattern from §2 above.

4. PSF ASCII Format (Spectre 23.1)

DC (dc_op.dc)

VALUE
"M5:ids" "A" -9.966831545702541e-06 PROP(
"units" "A"
)
"vout" "V" 3.902670762490046e-01

Pattern: "KEY" "UNIT" <float> — key is lowercase m5:ids, not M5:id.

AC (ac_gain.ac)

VALUE
"freq" 1.000000000000000e+00
"vout" (-1.188805328346738e+02 1.182042857455499e-03)

Pattern: "freq" <float> then "vout" (<real> <imag>) on the next relevant line.

Noise (noise_an.noise)

VALUE
"freq" 1.000000000000000e+01
"M2" ( ... per-device noise contributions ... )
...
"out" 1.491e-03          ← output noise [V/√Hz]
"in"  1.254e-05          ← input-referred noise [V/√Hz]
"gain" 1.189e+02         ← transfer function [V/V]

Critical: The "in" field is in V/√Hz (not V²/Hz). To convert to nV/√Hz:

noise_nv = in_value * 1e9    # ✓ CORRECT: V/√Hz → nV/√Hz

noise_nv = sqrt(in_value) * 1e9  # ✗ WRONG: treats as V²/Hz

Verify by checking the TYPE declaration section: "in" "V/sqrt(Hz)".

5. Phase Margin for Inverting Amplifiers

Problem

A 5T OTA (PMOS diff pair + NMOS mirror load) is inverting: vip↑ → vout↓. The atan2(im, re) phase at DC is ≈ ±180°, not 0°. Naively computing PM = phase_at_GBW + 180° gives values like 268° or -92°.

Fix: Fold to (0°, 180°)

pm_raw = phase_at_gbw + 180.0   # standard formula
pm = pm_raw % 360.0             # normalize to [0, 360)
if pm > 180.0:
    pm = 360.0 - pm             # fold to [0, 180]

For a single-pole system: PM ≈ 90° (correct). The folding handles both atan2 branch-cut cases (±180° at DC).

6. Slew Rate Measurement: Large-Signal Step Required

Problem

Using a small step (e.g., 1 mV) in an open-loop OTA transient analysis gives a misleadingly low slew rate (e.g., 0.08 V/µs instead of expected 6+ V/µs).

Root Cause

Small-signal steps produce a bandwidth-limited response, not a slew-rate-limited response. The output follows an exponential with time constant τ = 1/(2π·GBW), and the max dV/dt is limited by bandwidth, not tail current.

For 1 mV input × 119 V/V gain = 119 mV output swing — the OTA never enters slew limiting because the tail current can track the signal at all times.

Slew limiting occurs when the differential pair is fully steered to one side, so the output current is clamped to I_tail.

Fix

Use a step large enough to fully steer the diff pair (≫ 2×Vov of input pair):

// ✗ WRONG — small signal, measures bandwidth not slew rate
Vip (vip 0) vsource dc=VICM mag=1 type=pulse \
  val0=VICM val1=VICM+1m delay=500n rise=1n fall=1n width=1u period=3u

// ✓ CORRECT — 100mV step fully steers PMOS pair (Vov ≈ 120mV)
Vip (vip 0) vsource dc=VICM mag=1 type=pulse \
  val0=VICM val1=VICM+100m delay=500n rise=1n fall=1n width=1u period=3u

Verification

• Theoretical SR = I_tail / CL (e.g., 10 µA / 1 pF = 10 V/µs)
• Measured SR should be within ~50-100% of theoretical
• If SR ≪ theoretical, step amplitude is too small

7. ICMR from DC Sweep: Use Transistor Region, Not CM Gain

Problem

Sweeping VICM (both inputs together) and computing dVout/dVICM gives common-mode gain ≈ 0, not differential gain. This is correct behavior for an open-loop OTA without CMFB, but useless for ICMR determination.

Root Cause

ICMR is about the range where the OTA maintains differential gain, but a CM sweep only exercises CM rejection. Vout stays nearly constant throughout the valid ICMR range.

Fix: Check Saturation Regions

In the DC sweep PSF, each transistor's region field is saved (with save M1:oppoint ...). BSIM region codes:

• 0 = off, 1 = linear, 2 = saturation, 3 = subthreshold

ICMR = range where all transistors remain in saturation (region=2):

# Parse "M1:region" ... "M5:region" from dc_sweep PSF
all_sat = [all(regions[f"M{j}"][i] == 2 for j in range(1, 6))
           for i in range(len(vicm_vals))]
icmr_lo = next(v for v, s in zip(vicm_vals, all_sat) if s)
icmr_hi = next(v for v, s in zip(reversed(vicm_vals), reversed(all_sat)) if s)

Output Swing (from Same Data)

Output swing is determined by the output transistors' headroom:

• Vout_min = Vov_M4 (NMOS load enters linear)
• Vout_max = Vtail - |Vov_M2| (PMOS output enters linear)

Read vdsat from dc_op.dc oppoint data:

vov_m4 = abs(op["m4:vdsat"])     # NMOS load overdrive
vov_m2 = abs(op["m2:vdsat"])     # PMOS diff pair overdrive
vtail  = op["vtail"]
output_swing = (vtail - vov_m2) - vov_m4

8. ADE-Generated Netlist: Model Path Fails for Direct Invocation (SFE-868)

Problem

Running spectre input.scs directly on an ADE-generated netlist fails with SFE-868:

ERROR (SFE-868): Cannot open the input file
  '.../oa/smic13mmrf_1233/../models/spectre/ms013_io33_v2p6_7p_spe.lib'
ERROR (SFE-868): Cannot open the input file 'tt'
spectre terminated prematurely due to fatal error.

Root Cause

ADE generates model include paths using an OA-relative pattern:

include ".../oa/smic13mmrf_1233//../models/spectre/ms013_io33_v2p6_7p_spe.lib"
include "tt"

The .. goes up one level from smic13mmrf_1233/ into oa/ — resolving to oa/models/spectre/ which does not exist. When ADE runs spectre via runSimulation with +adespetkn=adespe, it uses OA-aware path resolution that bypasses this filesystem issue. Standalone spectre does plain filesystem .. traversal and fails.

Fix: Patch to Absolute Path Before Running

# Find the correct path (one level up from oa/):
# .../0.13um_1p3m_8k/oa/smic13mmrf_1233/../  →  .../0.13um_1p3m_8k/oa/  (wrong)
# correct:  .../0.13um_1p3m_8k/models/spectre/...

# Replace the two broken lines with a direct include + section:
sed -i \
  -e 's|include ".*/oa/smic13mmrf_1233//../models/spectre/ms013_io33_v2p6_7p_spe.lib"|include "/foundry/smic/013mmrf/pdk/20250911/cadence/0.13um_1p3m_8k/models/spectre/ms013_io33_v2p6_7p_spe.lib" section=tt|' \
  -e '/^include "tt"$/d' \
  input.scs

Or manually replace:

// ✗ ADE-generated (broken for standalone)
include ".../oa/smic13mmrf_1233//../models/spectre/ms013_io33_v2p6_7p_spe.lib"
include "tt"

// ✓ Direct path (works for standalone spectre)
include "/foundry/smic/013mmrf/pdk/20250911/cadence/0.13um_1p3m_8k/models/spectre/ms013_io33_v2p6_7p_spe.lib" section=tt

Warning: Patch Is Overwritten on Re-Netlist

Every vcli sim netlist --recreate regenerates input.scs with the broken ADE path. Reapply the patch after each re-netlist when using standalone spectre.

Also: vcli sim run Reports Success Even When Spectre Fails This Way

run() returns the resultsDir (non-nil = "success" to Ocean) the moment spectre is launched, before spectre's exit code is checked. Always verify:

tail -2 <resultsDir>/psf/spectre.out
# ✓ "spectre completes with 0 errors"
# ✗ "spectre terminated prematurely due to fatal error"
ls <resultsDir>/psf/*.dc 2>/dev/null || echo "NO DATA FILES — sim failed"

Quick Reference: Spectre Help

spectre -h vsource    # all vsource parameters (mag, dc, type, ...)
spectre -h noise      # noise analysis options (oprobe, iprobe, ...)
spectre -h resistor   # resistor element parameters

Notes

• These gotchas apply to netlist mode (spectre file.scs), not ADE-driven simulation
• In ADE/Virtuoso, noise setup is handled by the GUI and these issues don't arise
• The PSF ASCII format may vary slightly between Spectre versions; always verify with a small test file
• See also: skill-shell-gotchas for SKILL/IPC integration issues